Niveo NGSM48T2 Скачать руководство пользователя страница 293

Страница: 293 / 355

Chapter 5: Monitor, Diagnostic, Maintenance

Monitor, Diagnostic, Maintenance

NGSM48T2 User Manual | 293

State

The current state of the server. This field takes one of the following values:

Disabled:

The server is disabled

Not Ready:

The server is enabled, but IP communication is not yet up and running.

Ready:

The server is enabled, IP communication is up and running, and the

RADIUS module is ready to accept accounting attempts.

Dead (X seconds left):

Accounting attempts were made to this server, but it did not

reply within the configured timeout. The server has temporarily been disabled, but

will get re-enabled when the dead-time expires. The number of seconds left before

this occurs is displayed in parentheses. This state is only reachable when more than

one server is enabled.

Buttons

Auto-refresh:

Click this box to enable an automatic refresh of the page at regular

intervals.

Refresh:

Click to refresh the page immediately.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды