Niveo NGSM48T2 Скачать руководство пользователя страница 307

Страница: 307 / 355

Chapter 5: Monitor, Diagnostic, Maintenance

Monitor, Diagnostic, Maintenance

NGSM48T2 User Manual | 307

LACP Port Status

This page provides a status overview for LACP status for all ports.

Port

The switch port number.

LACP

'Yes' means that LACP is enabled and the port link is up. 'No' means that LACP is

not enabled or that the port link is down. 'Backup' means that the port could not join

the aggregation group but will join if other port leaves. Meanwhile it's LACP status is

disabled.

Key

The key assigned to this port. Only ports with the same key can aggregate together.

Aggr ID

The Aggregation ID assigned to this aggregation group.

Partner System ID

The partner's System ID (MAC address).

Partner Port

The partner's port number connected to this port.

Buttons

Refresh:

Click to refresh the page immediately.

Auto-refresh:

Click this box to enable an automatic refresh of the page at regular

intervals.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды