Niveo NGSM48T2 Скачать руководство пользователя страница 310

Страница: 310 / 355

Chapter 5: Monitor, Diagnostic, Maintenance

Monitor, Diagnostic, Maintenance

NGSM48T2 User Manual | 310

STP Bridge Status

This page provides a status overview of all STP bridge instances.

Bridge Status

The displayed table contains a row for each STP bridge instance, where the column

displays the following information:

MSTI

The Bridge Instance. This is also a link to the STP Detailed Bridge Status

Bridge ID

The Bridge ID of this Bridge instance.

Root ID

The Bridge ID of the currently elected root bridge.

Root Port

The switch port currently assigned the root port role.

Root Cost

Root Path Cost. For the Root Bridge it is zero. For all other Bridges, it is the sum of

the Port Path Costs on the least cost path to the Root Bridge.

Topology Flag

The current state of the Topology Change Flag of this Bridge instance.

Topology Change Last

The time since last Topology Change occurred.

Buttons

Refresh:

Click to refresh the page immediately.

Auto-refresh:

Check this box to enable an automatic refresh of the page at regular

intervals.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды