Niveo NGSM48T2 Скачать руководство пользователя страница 297

Страница: 297 / 355

Chapter 5: Monitor, Diagnostic, Maintenance

Monitor, Diagnostic, Maintenance

NGSM48T2 User Manual | 297

RADIUS Accounting Statistics

The statistics map closely to those specified in RFC4670-RADIUS.Accounting Client

MIB.

Use the server select box to switch between the backend servers to show details for.

Packet Counters

RADIUS accounting server packet counter. There are five receive and four transmit

counters.

Direction

Name

RFC4670 Name

Description

Responses

radiusAccClientExtRespons

The number of RADIUS packets (valid or

invalid) received from the server.

Malformed

Responses

radiusAccClientExtMalform

edResponses

The number of malformed RADIUS packets

received from the server. Malformed packets

include packets with an invalid length. Bad

authenticators or unknown types are not

included as malformed access responses.

Bad

Authenticators

radiusAcctClientExtBadAut

henticators

The number of RADIUS packets containing

invalid authenticators received from the

server.

Unknown Types

radiusAccClientExtUnknow

nTypes

The number of RADIUS packets of unknown

types that were received from the server on

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды