Niveo NGSM48T2 Скачать руководство пользователя страница 85

Страница: 85 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 85

Access Control List Configuration

This page shows the Access Control List (ACL), which is made up of the ACEs

defined on this switch. Each row describes the ACE that is defined. The maximum

number of ACEs is 256 on each switch.

Click on the lowest plus sign to add a new ACE to the list. The reserved ACEs used

for internal protocol, cannot be edited or deleted, the order sequence cannot be

changed and the priority is highest.

Ingress Port

Indicates the ingress port of the ACE. Possible values are:

All:

The ACE will match all ingress port.

Port:

The ACE will match a specific ingress port.

Policy / Bitmask

Indicates the policy number and bitmask of the ACE.

Frame Type

Indicates the frame type of the ACE. Possible values are:

Any:

The ACE will match any frame type.

EType:

The ACE will match Ethernet Type frames. Note that an Ethernet Type

based ACE will not get matched by IP and ARP frames.

ARP:

The ACE will match ARP/RARP frames.

IPv4:

The ACE will match all IPv4 frames.

IPv4/ICMP:

The ACE will match IPv4 frames with ICMP protocol.

IPv4/UDP:

The ACE will match IPv4 frames with UDP protocol.

IPv4/TCP:

The ACE will match IPv4 frames with TCP protocol.

IPv4/Other:

The ACE will match IPv4 frames, which are not ICMP/UDP/TCP.

IPv6:

The ACE will match all IPv6 standard frames.

Action

Indicates the forwarding action of the ACE.

Permit:

Frames matching the ACE may be forwarded and learned.

Deny:

Frames matching the ACE are dropped.

Rate Limiter

Indicates the rate limiter number of the ACE. The allowed range is 1 to 16. When

Disabled is displayed, the rate limiter operation is disabled.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Niveo NGSM48T2, Руководство пользователя, Страница: 85 / 355

Результаты поиска

Содержание NGSM48T2

Отзывы: