Niveo NGSM48T2 Скачать руководство пользователя страница 86

Страница: 86 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 86

Port Copy

Indicates the port copy operation of the ACE. Frames matching the ACE are copied

to the port number. The allowed values are Disabled or a specific port number.

When Disabled is displayed, the port copy operation is disabled.

Mirror

Specify the mirror operation of this port. Frames matching the ACE are mirrored to

the destination mirror port. The allowed values are:

Enabled:

Frames received on the port are mirrored.

Disabled:

Frames received on the port are not mirrored.

The default value is "Disabled".

Counter

The counter indicates the number of times the ACE was hit by a frame.

Modification Buttons

You can modify each ACE (Access Control Entry) in the table using the following

buttons:

: Inserts a new ACE before the current row.

: Edits the ACE row.

: Moves the ACE up the list.

: Moves the ACE down the list.

: Deletes the ACE.

: The lowest plus sign adds a new entry at the bottom of the ACE listings.

Buttons

Auto-refresh:

Check this box to refresh the page automatically. Automatic refresh

occurs at regular intervals.

Refresh:

Click to refresh the page. Note that non-committed changes will be lost.

Clear:

Click to clear the counter

Remove All:

Click to remove all ACEs

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Niveo NGSM48T2, Руководство пользователя, Страница: 86 / 355

Результаты поиска

Содержание NGSM48T2

Отзывы: