Niveo NGSM48T2 Скачать руководство пользователя страница 279

Страница: 279 / 355

Chapter 5: Monitor, Diagnostic, Maintenance

Monitor, Diagnostic, Maintenance

NGSM48T2 User Manual | 279

(right-most table).

Other

Requests

dot1xAuthBackendOtherRequestsToSupplicant

802.1X-based

Counts the number of times that the

switch sends an EAP Request packet

following the first to the supplicant.

Indicates that the backend server

chose an EAP-method.

MAC-based

Not applicable.

Auth.

Successes

dot1xAuthBackendAuthSuccesses

802.1X- and MAC-based

Counts the number of times that the

switch receives a success indication.

Indicates that the supplicant/client has

successfully authenticated to the

backend server.

Auth.

Failures

dot1xAuthBackendAuthFails

802.1X- and MAC-based

Counts the number of times that the

switch receives a failure message.

This indicates that the supplicant/client

has not authenticated to the backend

server.

Responses

dot1xAuthBackendResponses

802.1X-based:

Counts the number of times that the

switch attempts to send a supplicant's

first response packet to the backend

server. Indicates the switch attempted

communication with the backend

server. Possible retransmissions are

not counted.

MAC-based:

Counts all the backend server packets

sent from the switch towards the

backend server for a given port

(left-most table) or client (right-most

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Бренды по названию

Популярные бренды