Niveo NGSM48T2 Скачать руководство пользователя страница 294

Страница: 294 / 355

Chapter 5: Monitor, Diagnostic, Maintenance

Monitor, Diagnostic, Maintenance

NGSM48T2 User Manual | 294

RADIUS Authentication Statistics

This page provides detailed statistics for a particular RADIUS server.

RADIUS Authentication Statistics

The statistics map closely to those specified in RFC4668-RADIUS.Authentication

Client MIB.

Use the server select box to switch between the backend servers to show details for.

Packet Counters

RADIUS authentication server packet counter. There are seven receive and four

transmit counters.

Direction

Name

RFC4668 Name

Description

Access Accepts

radiusAuthClientExtAccess

Accepts

The number of RADIUS Access-Accept packets

(valid or invalid) received from the server.

Access Rejects

radiusAuthClientExtAccess

Rejects

The number of RADIUS Access-Reject packets

(valid or invalid) received from the server.

Access

Challenges

radiusAuthClientExtAcc

essChallenges

The number of RADIUS Access-Challenge

packets (valid or invalid) received from the

server.

Malformed

Access

radiusAuthClientExtMalf

ormedAccessResponse

The number of malformed RADIUS

Access-Response packets received from the

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Niveo NGSM48T2, Руководство пользователя, Страница: 294 / 355

Результаты поиска

Содержание NGSM48T2

Отзывы: