Niveo NGSM48T2 Скачать руководство пользователя страница 100

Страница: 100 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 100

Relay Information Policy

Indicates the DHCP relay information option policy. When DHCP relay information

mode operation is enabled, if agent receives a DHCP message that already contains

relay agent information it will enforce the policy. And it only works under DHCP if

relay information operation mode is enabled. Possible policies are:

Replace:

Replace the original relay information when a DHCP message that already

contains it is received.

Keep:

Keep the original relay information when a DHCP message that already

contains it is received.

Drop:

Drop the package when a DHCP message that already contains relay

information is received.

Buttons

Save:

Click to save changes.

Reset:

Click to undo any changes made locally and revert to previously saved

values.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Niveo NGSM48T2, Руководство пользователя, Страница: 100 / 355

Результаты поиска

Содержание NGSM48T2

Отзывы: