NewMar VENTANA 2022, Руководство пользователя

Страница: 211 / 238

© 2021 Copyright Newmar Corporation. All rights reserved. For the most up-to-date version of this content, and for more product-specific information, please refer to Newgle.
206
PLUMBING
Dometic MasterFlush Toilet Electronic Flush Switch
Panel Operation (Models: VFS, VFP, VFSHW, DFS,
DFP, DFSHW)
This article provides basic operational instructions for a Dometic MasterFlush Toilet Electric Switch Panel (VFS, VFP, VFSHW,
DFS, DFP, DFSHW).
Operating The Switches (8000
and 9000 Series Toilets)
For electronic MasterFlush toilets, these wall-mounted
flush switches and status panels feature streamlined
styling while delivering user-friendly push-button
operation. System status lights monitor vacuum level and
indicate when the toilet is properly energized for the next
flush.
TOILET SYSTEM STARTUP:
•
Turn ON electrical power and water supply to the
toilet.
•
Flush the toilet by pressing the Flush button or
waving a hand over the motion sensor(DFSHW only).
Allow the flush cycle to complete.
•
Toss several sheets of toilet tissue into the bowl and
flush the toilet again. The bowl should be completely
clear.
•
9000 Series: If the bowl is not completely clear after
flushing, adjust the rim and jet water flow timing on
the toilet control module to a higher setting. Repeat
the flush test after each adjustment.
NORMAL TOILET OPERATION (DFS,
DFP, AND DFSHW)
1. Press and hold the Add Water button until the desired
water level is achieved in the bowl.
2. Press the Flush button to flush the toilet.
3. Press the Add Water button twice quickly to toggle
through backlight modes:
•
Always ON (full brightness, default)
•
Always ON (dim) (DFSHW only)
•
Energy saving (ON when motion is sensed)
(VFSHW only)
•
Always OFF
CHANGING FLUSH MODES
1. Press and hold the Flush button for approximately
five seconds to toggle between normal and dry bowl
mode.
2. Release the Flush button when the OK TO FLUSH or
POWER light begins flashing.
Flush Mode Action Water Used Per Flush
Normal
Adds water to the bowl after
every flush
.85 gal (3.2 liters)
Dry bowl
Does not add water to the
bowl after every flush
.45 gal (1.7 liters)
**Flush actuation is disabled to prevent overfilling the holding tank.
Indicator Light Status
Power On Steady Green
Electrical power to the toilet is
activated.
Power On Flashing Green The flush mode is changing.
Tank Level Amber The holding tank is 75% full.
Tank Level Red The holding tank is 100% full.**
UNDERSTANDING THE INDICATOR
LIGHT
Source(s): Dometic Support MF-DFS Installation and Operator Manual
Product(s): This source is associated with more than one product. Refer to Newgle
for more information about the product(s) o ff ered for your coach’s model year.
USING THE HAND WAVE FEATURE
(MOTION-ACTIVATED DFSHW)
1. Hold your hand in front of the Motion Sensor to fill
the bowl with water. Water will start to flow after
three seconds. Continue to hold your hand in front
of the motion sensor until the desired water level is
achieved.
2. Wave your hand in front of the Motion Sensor to flush
the toilet.
3. The handwave function can be toggled on/o ff by
holding in BOTH the left and right buttons for 5
seconds. A backlighting fade sequence will follow
indicating the handwave operation has been toggled.
•
Backlight fade-to-on indicates handwave has been
toggled to ‘enabled’.
•
Backlight fade-to-o ff indicates handwave has been
toggled to‘disabled’.
The motion sensor range is 4” (10 cm).
IMPORTANT
!