© 2021 Copyright Newmar Corporation. All rights reserved. For the most up-to-date version of this content, and for more product-specific information, please refer to Newgle.
194
PLUMBING
5. AquaGo Comfort / AquaGo Comfort plus:
•
Select the desired operating mode.
•
Close the access door.
WARNING
!
Scalding injuries caused by hot water! Water
temperatures over 127ºF (52ºC) can cause severe
burns or scalding and in extreme cases even
death. Before using the hot water faucet or using
the shower, allow the hot water to run until the
water temperature no longer increases. Test the
temperature of the water before placing a child in
the bath or shower. Do not leave a child or an infirm
person in the bath unsupervised.
Switching On The Appliance
1. Open the access door.
2. To switch on the appliance, switch the POWER switch
to one of the two “ON” positions.
•
Both ON positions on the POWER switch have the
same function. Choose your preferred position.
•
When the green power ON LED 1 is lit, the
appliance is switched on.
•
If the red error code LED 2 is lit / flashes, there is a
fault or warning.
•
There may be a variation between the temperature
delivered from the appliance and the temperature
at the faucet due to water conditions or the length
of pipe from the appliance.
•
The presence of a flow restrictor in the hot water
line may Iimit the water flow.
How to use hot water:
•
To obtain the desired water temperature at the
faucet or in the shower, mix cold and hot water.
•
Particularly when showering, wait until the water
temperature has stabilized before entering or
allowing other people or animals to enter the
shower.
•
The appliance is now ready for using the control
panel inside your vehicle.
AQUAGO COMFORT / AQUAGO
COMFORT PLUS
With the rotary switch you can choose between the
following operating modes:
Operating Modes (Control
Panel)
Symbol /
Operating Mode Description
ECO
The appliance is now running in energy-saving mode.
•
Water temperature at the outlet is approximately 120
°F (49 °C).
•
Prevention of freezing by using propane gas. The
temperature in the appliance is automatically kept
above 41 °F (5 °C).
•
During operation, the yellow status LED 3 is lit.
COMFORT
The appliance is now running in a mode that provides rapid
availability of hot water.
•
Water temperature at the outlet is approximately 120
°F (49 °C).
•
Stand-by heat. The temperature in the appliance is
automatically kept above 102 °F (39 °C).
•
During operation, the yellow status LED 3 is lit.
OFF
Stand-by. The appliance is not running in any operating
mode.
•
The yellow status LED 3 is o
ff
. To switch o
ff
the
POWER and gas supply, refer to “Switching OFF the
appliance”.
ANTIFREEZE
Prevention of freezing using 12 VDC electricity:
•
Operating mode with installed electric antifreeze kit
(available as an accessory) and appliance switched
on. The temperature in the appliance is automatically
kept above 41 °F (5 °C).
•
During operation, the yellow status LED 3 is lit.
CLEAN
Decalcification. Only AquaGo Comfort / AquaGo Comfort
plus. See “Decalcification”.
•
For safety reasons, after 30 seconds the
decalcification process cannot be stopped until
the system has been rinsed in accordance with the
instructions. See “Interrupting decalcification”.
A control panel to select the operating mode.
AQUAGO COMFORT / AQUAGO
COMFORT PLUS
DESCRIPTION OF THE YELLOW
STATUS LED 3
Signal
Meaning
LED 3 is lit
Appliance is switched ON
LED 3 is o
ff
Appliance is switched OFF.
Every 7 s, LED 3 is interrupted
for 1 s
The appliance must be decalcified
LED 3 flashes slowly 1 s on, 1 s o
ff
Decalcification mode has been activated
LED 3 flashes quickly
Before you use the water system you must
rinse it.
LED 3 flashes 2 x briefly after a
break.
There is a fault in the appliance. The exact
fault diagnosis must be determined via error
LED 2. Risk of freezing if the temperature in
the appliance is below 37.4 °F (3 °C).
Содержание VENTANA 2022
Страница 1: ...SM 2022...