NewMar VENTANA 2022, Руководство пользователя

Страница: 184 / 238

© 2021 Copyright Newmar Corporation. All rights reserved. For the most up-to-date version of this content, and for more product-specific information, please refer to Newgle.
179
INTERIOR
If the code fails, go through steps 1-3
again. If the code works successfully,
then you should lock the safe.
When you open the safe in the future,
enter the security code you have set,
followed by the checkmark yet, and
turn the knob.
If an incorrect security code is entered
3 times, the safe will beep 5 times (if
the sound is turned on) and the red
light will flash 5 times resulting in
the safe being automatically locked out for 60 seconds
before you can try your code again. The safe will beep
one time (if the sound is turned on) and the green light will
flash once when the lockout period is over.
If an incorrect security code is entered 1 additional time,
the safe will beep 5 times (if the sound is turned on) and
the red light will flash 5 times, resulting in the safe being
automatically locked out for 5 minutes before the code
can be tried again. The safe will beep one time (if the
sound is turned on) and the green light will flash once
when the lockout period is over.
This key can be found inside the coach information
packet. This is the black bag containing user manuals
and other coach-specific documentation. If the key
is not available, the default code set by the factory
is “1-5-9,” followed by the green checkmark button.
This code will only work if the batteries have already
been installed and a security code has NOT yet been
entered.
NOTICE
!
Note: This key has been
provided in case you lose
or forget your security code
or the batteries run low. If
you lose your key, you may
purchase a replacement key
by referencing the serial
number located under the
removable lock cover. See
the section at the end of
these instructions regarding
replacement keys.
Locate the batteries inside
the safe. Open the battery
compartment on the back of
the door by pushing the tab
in the direction of the arrow and install the batteries.
Note: The reset button located on the inside of the door
is covered with a removable cap. When you use the reset
button while setting your own combination, remove the
cap to access the button. Use the tip of a ballpoint pen or
the end tip of a paper clip to push the reset button.
Replace the cap securely over the reset button after
setting your combination. Failure to do so will compromise
the safety and security of the safe.
Entering Your Security Code
To enter your own security code you will need to follow
the steps listed below:
1. After installing the batteries, locate the reset button
on the back of the door.
2. Press the reset button with a pen and then release it;
you will hear a beep. Do NOT shut the door until you
have confirmed that your new security code has been
entered correctly.
3. With the door open, enter your own personal security
code, which can be 3-8 digits long, and confirm your
new code by pressing the checkmark key on the
electronic touch pad. You will have 3 seconds to
press the checkmark key, otherwise you will have to
start over from step one. There will be 2 beeps (if the
sound is turned on) and the green light will flash twice
if your code has been entered successfully. Before
you close the door, enter the new security code
and press the checkmark key to make sure the lock
releases the knob so you can turn it and retract the
live action locking bolts.
If you write down your combination, you must keep
this information in a secure place, away from children,
not inside the safe.
IMPORTANT
!
Locking The Safe
To lock the safe, close the door and turn the knob to the
left to the 12:00 position.
Battery Replacement
This safe uses 4 - AA batteries. Under normal use,
batteries will last about 1 year.
•
Do not mix old and new batteries.
•
Do not mix alkaline, standard or rechargeable
batteries.
If the batteries are low, the yellow light will flash when
you start to enter your code. To replace the batteries,
open the battery compartment on the back of the door by
pushing the tab in the direction of the arrow and install all
new batteries.
Internal LED Light
This safe includes an internal LED light that will activate
when the correct combination is entered and will remain
on for 30 seconds.
Turning The Keypad Sound
Off/On
Your safe comes with the “Beep” sound turned on. You
can turn o ff the “Beep” sound of the keypad by pressing
the Volume key. To turn the “Beep” sound on, press the
Volume key again.
Product(s): Stack-On PWS-1822-E Security Wall Safe Owner’s Manual(Model: PWS-
1822-E, Newmar Part Number: 144484)