Ness D16 Скачать руководство пользователя страница 52

Страница: 52 / 64

P R O G R A M M I N G

NESS D16 (V4.6) CONTROL PANEL - INSTALLER MANUAL

1E 2E 3E 4E 5E 6E 7E 8E

ON = Factory default setting.

Upload/DownloadDirect Connect R

emote Ar

ming

emote Disar

ming

emote A

UX control

emote Status repor

ting

emote Event repor

ting

Callback mode

OPTION No

DESCRIPTION

P90E

Upload/Download options

REMOTE ACCESS

When selected On, this option allows the panel to be remotely upload/
downloaded by a remote computer or controlled by a remote telephone.

When the option is Off, the panel will not answer incoming telephone calls,
preventing any type of remote access.

PROGRAMMING SEQUENCE:

P90E 1E

toggles the option ON and OFF

P90E 1E OFF: No Remote Access
P90E 1E ON:

Remote Access enabled

P90E 1E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: No Remote Access

NOTES:

• RELATED OPTIONS:

P91E

Required Rings

DIRECT CONNECT

This allows a direct connection to be used between the D16 telephone output
and an on site computer with modem.

Direct Connect simulates a telephone line ring and makes the D16 connect
immediately to the telephone line.

SEQUENCE:

• The panel must be in Installer Program mode.
• Dial the panel using NessComms™.
• While NessComms is ringing the panel, press P90E 2E.
• This forces the panel to pick up the line and comms can start.

P90E 2E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: No Direct Connect

NOTES:

• Remote Access must also be enabled

• RELATED OPTIONS:

P90E 1E

Enable Upload/Download

REMOTE ARMING

Allows the remote Arming of the control panel using a standard DTMF
telephone (or mobile phone) from anywhere in the world.

PROGRAMMING SEQUENCE:

P90E 3E

toggles the option ON and OFF

P90E 3E OFF: No Remote Arming
P90E 3E ON:

Remote Arming enabled

P90E 3E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: No Remote Arming

NOTES:

• Remote Access must also be enabled

• RELATED OPTIONS:

P90E 1E

Enable Upload/Download

• See page 62 for details on Remote

Operation by telephone

MODEM

12V BATTERY

270R

605

Plug

605

Plug

D16 Control Panel

COMPUTER

DIRECT CONNECT Diagram
Upload/download on site

Technical Manuals Online! - http://www.tech-man.com

Содержание D16

































































Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды

Ness D16, Инструкция по установке и программированию

Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды