Ness D16 Скачать руководство пользователя страница 51

Страница: 51 / 64

P R O G R A M M I N G

NESS D16 (V4.6) CONTROL PANEL - INSTALLER MANUAL

SWINGER SHUTDOWN

Limits the number of calls made by a zone alarm when Multiple Zone Alarms
are enabled for that zone.

If enabled, multiple reports are limited to three per zone.

PROGRAMMING SEQUENCE:

P89E 4E

toggles the option ON and OFF

P89E 4E OFF: No Swinger Shutdown (unlimited multiple reports)
P89E 4E ON:

Swinger Shutdown enabled (maximum 3 reports per zone)

P89E 4E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

ON: Swinger Shutdown enabled

NOTES:

• This prevents unnecessary multiple

alarms reported to the Central station in
cases, for example, where a door is
‘swinging’ in the wind.

LINE FAULT MONITOR

When this option is enabled, the telephone line is regularly tested. If the
telephone line is not found, the Line light will commence flashing.

PROGRAMMING SEQUENCE:

P89E 5E

toggles the option ON and OFF

P89E 5E OFF: No Line Fault Monitor
P89E 5E ON:

Line Fault Monitor enabled

P89E 5E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: No Line Fault Monitor

NOTES:

• RELATED OPTIONS:

P89E 6E

Line Fault to AUX2

LINE FAULT TO AUX2

When this option is enabled, a telephone line fault condition will turn ON the
AUX2 output. AUX2 will turn OFF when the telephone line is restored.

PROGRAMMING SEQUENCE:

P89E 6E

toggles the option ON and OFF

P89E 6E OFF: No Line Fault output
P89E 6E ON:

Line Fault to AUX2 enabled

P89E 6E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: No Line Fault output

NOTES:

• RELATED OPTIONS:

P89E 5E

Line Fault Monitor

CLOCK TIMING

When set ON, the Test Report Timer uses the panel’s onboard crystal oscillator
instead of the external mains power supply frequency.

Use this option if the mains frequency is not stable over long periods. (Not
necessary in Australia and New Zealand).

PROGRAMMING SEQUENCE:

P89E 7E

toggles the option ON and OFF

P89E 7E OFF: Clock uses mains frequency timing
P89E 7E ON:

Clock uses internal timing

P89E 7E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: Clock uses mains frequency timing

NOTES:

Technical Manuals Online! - http://www.tech-man.com

Содержание D16

































































Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды

Ness D16, Инструкция по установке и программированию

Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды