5
5
5
5
5
NESS D16 (V4.6) CONTROL PANEL - INSTALLER MANUAL
INSTALLATION PROCEDURES
The location of the main panel housing should be in an area that is within the
protected area of the premises. A linen closet or cupboard are good examples
as these are generally located in the centre of the Premises.
Positioning of the movement detectors should be considered as the incorrect
position may cause unwanted alarms.
1.
Unclip the lid by pushing in the directions of the arrows 1 and 2 as shown below.
2.
Remove the Battery from the base.
3.
Mount the rear panel housing to a secure location.
4.
Insert the PCB stand-offs in the Panel and then plug the circuit board onto the stand-offs.
5.
Wire to the circuit board terminal blocks, as per the wiring instructions shown in this
installation manual.
6.
Replace the Battery.
7.
Insert the panel tamper bracket as shown at left.
8.
Program the control panel as required
1
2
INSTALLING PCB STANDOFFS
& TAMPER BRACKET
HOW TO REMOVE THE LID
PACKING LIST
100-687 Ness D16 Control Panel
Q T Y
Q T Y
Q T Y
Q T Y
Q T Y DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
1
D16 main board
1
D16 housing
1
Ness LCD keypad (100-667)
1
17VAC plug pack
1
12V 7Ah battery (optional)
1
Dialler telephone lead
1
User manual
1
Installer manual
9
2.2K End Of Line resistors
8
4.7K End Of Line resistors
1
Lead assembly for Battery
1
Lead assembly for Internal Tamper
1
Tamper bracket
1
Zone list label
2
Housing cover screws
2
Circuit board standoff
D16 SPECIFICATIONS
Box construction ............ 3mm Polycarbonate (equiv. 1.2mm mild steel)
Box Dimensions ............. 223W x 300H x 85D mm
Plug Pack ...................... 240Vac, output [email protected]
Power Supply ................ 13.8Vdc @ 800mA
Quiescent Current ......... 80mA with 1 Keypad
Operating Voltage ........ 9.5V- 14V dc
Rechargeable Battery ... 12 volt 7.0 Amp/hour, lead acid
Battery Charging current
350mA maximum, current limited
Dynamic Battery Test .... Every Hour and on arming 10.75V with a 5 amp load
Fuses ............................. 2 Amp resettable / sirens & reset.
500mA resettable / 12 volt auxiliary outputs
200 mA resettable / strobe output
INPUTS .......................... 8 physical Zone inputs
(16 Zones inputs with Zone Split enabled)
2 physical 24hr Tamper inputs
End of line resistor ......... 2200 Ohm (or Zone Split 2200 Ohm & 4700 Ohm)
Remote Keypad input .... Proprietary
Maximum Keypads ........ 3
J2 Header ...................... Multi-pin connector for the Ness Radio Interface (100-200)
OUTPUTS
Siren ............................... On board siren driver. Timed output.
Maximum 3 x 8 Ohm horn speakers
Strobe ............................ 12V DC timed output. Maximum 2 x 1 Watt strobe lights
Reset .............................. 12V DC timed output. Maximum 3 x 12V piezo screamers
Equipment power output 13.8V DC output for powering detectors and other equipment.
Maximum 500mA.
J3 Header ...................... Multi-pin connector provides the outputs AUX1, AUX2, ARM1,
ARM2, 12V DC. Also used to connect to the D16 Output Expander
(100-699).
Technical Manuals Online! - http://www.tech-man.com
