manualshive.com logo in svg

NeoDen 800, Руководство пользователя, Страница: 81 / 88

Поделиться
Скачать
NeoDen 800 Скачать руководство пользователя страница 81

77

Solution: open the back cover of the machine, use a multimeter to inspect, and lock the loose
part.

5. Black screen of display

Reason: the display power supply is not turned on or the signal line is not connected properly

Solution: check the power and signal lines of the monitor.

6. The component frame offsets when moving the camera left and right or back and forth

Cause: lens calibration is not accurate.

Solution: calibrate the lens. Select a clear character or positioning hole on the surface of the
currently inspected PCB for lens calibration. There should be no similar pattern near the
calibration area, otherwise the calibration result will be inaccurate.

7. Too many misjudgments in normal inspection

Reason 1: the component frame offsets

Solution:

①

Check whether the PCB is fixed and fix the PCB and fixture.

②

Make the machine return to the calculation starting point to inspect whether

the coordinates of the components offset as a whole. Then, reset the
coordinate starting point.

Reason 2: incoming materials are changed (stand-by materials are used)

Solution: re-register a standard with new components and include the component standard

and the newly-built standard into the same group.

Reason 3: inadequate learning and debugging lead to false report.

Solution: debug a few more boards.

8. Missing judgment of component

Reason 1: the component has no registered standard

Solution: register standard for the component and optimize the lens.

Reason 2: there is no lens optimization after adding components.

Solution: optimize the lens

Reason 3: the error range of the standard linked to the component is too large.

Solution: reduce the error range of the component standard by reducing the error multiple or

re-register a standard to replace the component standard.

9. Constant offset or reversal of several components during inspection

Reason 1: the component frame has offset.

Solution: move the lens to the position of the component and pull the component frame

Содержание 800

























































































Отзывы:

Нет отзывов