NeoDen 800 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 88

NeoDen 800 Скачать руководство пользователя страница 39

35

Adjust the size of each frame, and then register the component according to the method of
capacitance and resistance. If there are the same components, copy them in the same way.

Triode: [Triangle] can be directly selected for making frame based on the noumenon of triode. As
shown in the following figure:

Adjust the size of each frame, and then register the component according to the method of
capacitance and resistance. If there are the same components, copy them in the same way.

IC: the SOP frame can be directly selected to make the combined frame. However, because there
are many types of IC components, we generally choose our own frame combination. In the
following steps, take our own frame combination as an example, first select [Short Circuit Frame]
to make the solder leg frames on both sides, as shown in the following figure:

After that, the property interface of the component box will be displayed at the same time. If it
doesn't come out, click the selected box with the left mouse button, and the property interface
will also be displayed. Now check the polarity direction in the middle. [Top], [Bottom], [Left]
and [Right] represent the position of the small arrow on the component frame. After checking, let
the arrow point to the noumenon of IC. Then click [Short Circuit Setting] to enter the setting
interface. As shown in the following figure:

«
...
37
38
39
40
41
...
»

Содержание 800

























































































Отзывы:

Нет отзывов