NeoDen 800 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 88

NeoDen 800 Скачать руководство пользователя страница 57

53

Rotate different angles in the frame, horizontally mirror and vertically mirror to match the
position of coordinate points with components on PCB board, and then drag a coordinate point
on the left figure to correct it, as shown above.

Then edit the component.The selection of the component frame is the same as manual editing, as
shown in the following figure:

This interface will be prompted after the component frame is made. Click [Yes], and the
component will be automatically registered and the inspection frame of the components of the
same item will be automatically generated. However, after the component frame is registered, its
size cannot be modified. Only the property interface of the component frame can be modified. If
you need to change the size of the component frame after making the frame, click [No]. At this
time, the component frame is not registered and you can change its size. Register it after proper
adjustment. When registering, the item number will be automatically generated for this
coordinate. After clicking [OK], the inspection frame of the components of the same item

«
...
55
56
57
58
59
...
»

Содержание 800

























































































Отзывы:

Нет отзывов