MROTEK PINE-16M Скачать руководство пользователя страница 65

Страница: 65 / 100

4.11 Central site VCC configuration list of PINE-16M

4-49

4.11 Central site VCC configuration list of PINE-
16M

The network management configuration for PINE-16M is nothing but the network management
configuration for the 16 channels.

4.11.1 Enabling the VCC channel

The command and steps for enabling network management channel (VCC) is shown in the table below.
The network management channel is disabled by default.

Command Description

Config

Enter the global configuration mode.

interface vcc

Enter the central site VCC configuration mode of PINE-
16M.

vcc-channel

enable

Enables the VCC channel

show interface

Shows the configuration information

Example:

Mro-tek#

config

Mro-tek(config)#

interface

vcc

Mro-tek(config-vcc)#

vcc-channel

enable

Set Successfully.

Mro-tek(config-vcc)#

show interface

Channel Description IPAddress Netmask Enable

16 192.168.5.28 255.255.255.0 enable

Mro-tek(config-vcc)#

4.11.2 Disable VCC channel

Command Description

config

Enter the global configuration mode

interface vcc

Enter the central site VCC configuration mode of PINE-16M.

vcc-channel disable

Disable the VCC channel

show interface

Shows the configuration information

Example:

Mro-tek#

config

Mro-tek(config)#

interface

vcc

Содержание PINE-16M




































































































Результаты поиска

Содержание PINE-16M

Отзывы:

Похожие инструкции для PINE-16M

Бренды по названию

Популярные бренды

MROTEK PINE-16M, Руководство по настройке

Результаты поиска

Содержание PINE-16M

Отзывы:

Похожие инструкции для PINE-16M

Бренды по названию

Популярные бренды