MROTEK PINE-16M Скачать руководство пользователя страница 29

Страница: 29 / 100

Configuration of the Ethernet interface of PINE-16M

4-13

4.5.5 Flow control function

Flow control on the direction of transmitting and receiving of the port are configured at the same time, that
is, they can only be opened or closed simultaneously.

By default, the flow control function is enabled.

Command Description

config

Enter the global configuration mode.

interface eth

<1-2>

To Select a specific Ethernet interface of PINE-16M.

flow-control (on|off)

To Enable/Disable the flow control function.

show interface

Shows configuration information of the interface.

Example:

Mro-tek#

config

Mro-tek(config)#

interface eth

Mro-tek(config-eth/0/1)#

flow-control

setup successfully!

Mro-tek(config-eth/0/1)#

4.5.6 Clear the counter

The Counters of Ethernet port counters like input/output broadcast/multicast packets count, discarded
packets and other counters.

Command Description

config

Enter the global configuration mode

interface eth

<1-2>

Enter the central site Eth configuration mode of PINE-16M.

clear statistic

Clear the statistic counter

show interface

Show the configuration information of the interface.

Example:

Mro-tek#

config

Mro-tek(config)#

interface eth

Mro-tek(config-eth/0/1)#

clear statistic

setup successfully!

Mro-tek(config-eth/0/1)#

Содержание PINE-16M




































































































Результаты поиска

Содержание PINE-16M

Отзывы:

Похожие инструкции для PINE-16M

Бренды по названию

Популярные бренды

MROTEK PINE-16M, Руководство по настройке

Результаты поиска

Содержание PINE-16M

Отзывы:

Похожие инструкции для PINE-16M

Бренды по названию

Популярные бренды