MROTEK PINE-16M Скачать руководство пользователя страница 39

Страница: 39 / 100

4.9 Configuration of Central Site Switching of PINE-16M

4-23

Set up outer Tag TPID

By default, the TPID of outer Tag is 0x9100 and the users are authorized to specify the TPID value.

Command Description

config

Enter the global configuration mode.

double-tagging tpid

HHHH

To specify the TPID value.

show esw

Shows the basic information of Ethernet
switching.

The command

no double-tagging tpid

is available to restore the outer Tag TPID value to default value.

Example

: set the third global outer Tag TPID value to 0x8100.

Mro-tek#

config terminal

Configuration mode, one conmmand input per time. End with CTRL-Z.

Mro-tek(config)# double-tagging tpid 0x8100

tpid of slot 0 has been set.

Mro-tek(config)#

show esw

ethernet switch information for slot 0 for PINE-16M:

double-tagging tpid: 0x8100

use-core-tag disabled

trunk group disabled

double tagging supported

19 ports

no special port

Mro-tek(config)#

4.9.2 Management of MAC Address Table

Configure aging time for MAC address

Users can configure the aging time for the MAC address table and stop the aging of a MAC address using
the below given set of commands. By default, the aging time is 300 seconds.

Command Description

config

Enter the global configuration mode.

mac-address-table aging-time

<0-3825>

To Configure aging-time for MAC address table

show mac

Shows the basic information of MAC address management.

The command

no mac-address-table aging-time

is available for users to restore the aging-time to the

default value.

To disable the MAC address aging, define the aging time as 0.

Содержание PINE-16M




































































































Результаты поиска

Содержание PINE-16M

Отзывы:

Похожие инструкции для PINE-16M

Бренды по названию

Популярные бренды

MROTEK PINE-16M, Руководство по настройке

Результаты поиска

Содержание PINE-16M

Отзывы:

Похожие инструкции для PINE-16M

Бренды по названию

Популярные бренды