MROTEK PINE-16M Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 100

background image

4.9 Configuration of Central Site Switching of PINE-16M

4-28

Configure the mirror ports for the mirror function

As the mirror function takes effect, the message going in or out of a mirror port is copied and sent to the
monitor port. Mirror rule is established when the corresponding mirror port is configured. The available
rules are both, ingress or egress. The monitor port is not allowed to be configured as a mirror port.

1

. Both: mirror the message on both directions of the port

Command Description

Config

Enter the global configuration mode.

mirror source-port-list both

PORTLIST

Configure mirror port and mirror rule for bi-directional traffic.

show mirror

Shows the configuration of mirror function

2

. Ingress: mirror the message goes into the port

Command Description

Config

Enter the global configuration mode.

mirror source-port-list ingress

PORTLIST

Configure mirror port and mirror rule for ingress traffic

show mirror

Shows the configuration of mirror function

3

. Egress: mirror the message goes out of the port

Command Description

Config

Enter the global configuration mode

mirror source-port-list ingress

PORTLIST

Configure mirror port and mirror rule for egress traffic

show mirror

Show the configuration of mirror function

Configuring a new mirror port will erase the previous mirror configuration of the port.

The command no mirror monitor-port is available to delete a mirror port and to disable the mirror function

Enabling and disabling the configuration of mirror function

The configuration will take effect when the mirror function is enabled. A monitor port must be specified
before enabling the mirror function.

Command Description

Config

Enter the global configuration mode

mirror monitor-port

<1-19>

Configure a monitor port

mirror

{enable|disable}

Enable or disable the mirror function

show mirror

Shows the configuration of the mirror function

Example:

Configuring port 9 as the monitor port and port 1-8 as mirror ports and the mirror rule is

ingress.

Mro-tek#

config

«
...
42
43
44
45
46
...
»

Содержание PINE-16M





































































































Отзывы:

Нет отзывов

Похожие инструкции для PINE-16M

Бренд: takepayments Страницы: 4

Бренд: DT Research Страницы: 4

Бренд: National Instruments Страницы: 4

Бренд: National Instruments Страницы: 12

Бренд: BURGER KING Страницы: 20

Бренд: Redline Страницы: 106

Multitron GS-44

Бренд: GinSan Страницы: 2

Бренд: RETRIEVER Страницы: 2

Бренд: Ingenico group Страницы: 24

Бренд: Datalogic Страницы: 2

Бренд: NCR Страницы: 140

Бренд: Raveon Technologies Corporation Страницы: 21

Бренд: Teltonika Страницы: 16

Бренд: Toppan Forms Страницы: 6

Бренд: steute Страницы: 11

FlexSys Elan-06R-180

Бренд: Johnson Controls Страницы: 2

Бренд: Johnson Controls Страницы: 82

Бренд: Fundtech Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды