MROTEK PINE-16M Скачать руководство пользователя страница 76

Страница: 76 / 100

5.5 Configuring the Ethernet interface on remote inverse
multiplexer device

5-8

Mro-tek(config-eth/0/8/1)#

show interface

5.5.3 Setting Rate and duplex mode for the interface

The rate and duplex mode of the interface can only be configured when the auto-negotiation function is
disabled.

Command Description

Config

Enter the global configuration mode

remote

0 <1-16>

Enter the remote inverse multiplexer device’s configuration mode.

interface eth 1

Enter the eth configuration mode of remote inverse multiplexer
device

speed

(100|10)

duplex

(full|half)

Set up the rate and duplex mode for the interface.

show interface

Show the configuration information

This command is only applicable for inverse multiplexer device with electrical interfaces, including PINE-
iE1 and PINE-8.

Example:

Configure the remote Inverse multiplexers Ethernet interface for 10 Mbps Half-duplex mode

Mro-tek#

config

Mro-tek(config)#

remote 0 8

Mro-tek(config-remote/0/8)#

interface eth 1

Mro-tek(config-eth/0/8/1)#

speed

10 duplex half

Mro-tek(config-eth/0/8/1)#

show interface

5.5.4 Setting flow control function

Command Description

config

Enter the global configuration mode.

remote

0 <1-16>

Enter the remote inverse multiplexer device configuration mode.

interface eth 1

Enter the eth configuration mode of remote inverse multiplexer device.

interface fx-eth 1

Enter the fx-eth configuration mode of remote inverse multiplexer device.

flow-control

(on|off)

Enable / Disable the flow control function

show interface

Shows the configuration information

This command is applicable to all remote inverse multiplexer devices.

Example 1

: Configuring the flow control of the Ethernet interface of PINE-8

Mro-tek#

config

Mro-tek(config)#

remote

0 8

Mro-tek(config-remote/0/8)#

interface eth 1

Mro-tek(config-eth/0/8/1)#

flow-control on

Mro-tek(config-eth/0/8/1)#

show interface

Содержание PINE-16M




































































































Результаты поиска

Содержание PINE-16M

Отзывы:

Похожие инструкции для PINE-16M

Бренды по названию

Популярные бренды

MROTEK PINE-16M, Руководство по настройке

Результаты поиска

Содержание PINE-16M

Отзывы:

Похожие инструкции для PINE-16M

Бренды по названию

Популярные бренды