MROTEK PINE-16M Скачать руководство пользователя страница 19

Страница: 19 / 100

The configuration of central site E1 interface of PINE-16M

4-3

Configure loop back of remote E1 interface

Command Description

config

Enter the global configuration mode.

interface e1

<1-16>

To select a specific E1 interface at central site PINE-16M.

[no] remote-e1-loopback

To Enable remote E1 loopback for the selected E1 interface

show interface

Shows the configuration information of the interface.

Example:

Mro-tek#

config

Mro-tek(config)#

interface e1 1

Mro-tek(config-e1/0/1)#

remote-e1-loopback

Set Successfully.

Mro-tek(config-e1/0/1)#

Configure the loop back of the E1 interface

Command Description

config

Enter the global configuration mode

interface e1

<1-16>

To select a specific E1 interface at central site PINE-16M

[no] local-e1-loopback

To Enable Local E1 loop back for the selected E1 interface.

show interface

Shows the configuration information of the interface.

Please ensure to disconnect the E1 cables at the remote location before initiating the
loopbacks as it may lead to device abnormity..

Example:

Mro-tek#

config

Mro-tek(config)#

interface e1

Mro-tek(config-e1/0/1)#

local-e1-loopback

Set Successfully.

Mro-tek(config-e1/0/1)#

Содержание PINE-16M




































































































Результаты поиска

Содержание PINE-16M

Отзывы:

Похожие инструкции для PINE-16M

Бренды по названию

Популярные бренды

MROTEK PINE-16M, Руководство по настройке

Результаты поиска

Содержание PINE-16M

Отзывы:

Похожие инструкции для PINE-16M

Бренды по названию

Популярные бренды