MOTO GUZZI NORGE GT 8V Скачать руководство пользователя

Страница: 99 / 357

This option deletes instrument panel errors only, a further confirmation is requested.

INSTRUMENT PANEL SOFTWARE UPGRADE

This function is used to program the instrument

panel again with a new software through Naviga-

tor.

The Display reads: "Instrument panel disconnec-

ted. Now connect the diagnosis instrument"; the

instrument panel will connect normally after the

key is extracted-inserted.

The white connector is placed under the saddle,

beside the fuse box, close to the diagnosis con-

nector for the injection system.

Use the Ditech connector in the Navigator

Aprilia-

Moto Guzzi

package to connect to the Navigator

cable.

KEY CHANGE FUNCTION

This function can be used:

1) if one key is lost; the dealer can disable this key;

2) to activate up to 4 keys;

3) should a new key lock be necessary and thus program the new set of keys.

In the first phase the user code must be entered and, after confirming the inserted key (key I) has been

programmed, the other keys must be entered too.

The procedure finishes once the 4 keys have been programmed or after 20 seconds.

Should a new key lock be necessary, the procedure is: once the key is set to ON but the instrument

panel does not recognise it, the user code is requested: enter the user code.

Now enter MENU, DIAGNOSIS (entering the service code), KEY CHANGE and program the new keys.

Battery recharge circuit

Norge GT 8v

Electrical system

ELE SYS - 99

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды