MOTO GUZZI NORGE GT 8V Скачать руководство пользователя

Страница: 105 / 357

LOCATION ON THE VEHICLE:

Under the bevel

gear set box, right side.

CONNECTOR LOCATION (if available):

Under

the saddle, right side.

PIN-OUT:

•

PIN1 - Ground

•

PIN2 - Signal

NAVIGATOR

Parameters:

Speed (km/h) - Vehicle speed.

ELECTRICAL ERRORS

Speed sensor

5DA0 electric malfunction:

Electrical fault in sensor or cable harness.

Troubleshooting:

Perform the check procedure of the sensor connector and of the ABS control unit

connector, if not OK restore the connectors, if OK check the continuity of the yellow cable between

cable harness side sensor PIN 2 and ABS control unit connector PIN 11. If there is no continuity, restore

them. If there is, PIN 2 of the sensor on the cable harness side, with the sensor disconnected and key

set to ON, must have 12V voltage approximately: if there is no voltage, check PIN 2 for continuity with

the vehicle ground connection: if it is grounded, restore the cable harness. If OK, replace the control

unit. If PIN 2 has approx. 12 V, check continuity of the yellow/brown cable between PIN 1 of the sensor

on the cable harness side and PIN 12 of the ABS control unit connector. If this is not OK, restore the

cable harness. If it is OK, replace the sensor.

LOGIC ERRORS

Speed sensor

5DA1 the signal works irregularly:

faulty sensor or signal interference.

Troubleshooting:

Check speed sensor retainer. If it is not OK, restore it. If it is OK, check if the tone

wheel is dirty, deformed or wrongly fixed. If any of this happens, replace the tone wheel. Otherwise,

replace the speed sensor.

5DA2 the signal decreases periodically:

Possible tone wheel fault due to deformations or dirt; pos-

sible alterations on the wheel bearing surface. In very rare cases, abnormal tone wheel vibrations.

Troubleshooting:

Check if the tone wheel is dirty, deformed or wrongly fixed. If the tone wheel is not

OK, replace it. If it is OK, check for possible faults in the wheel bearings and if it is not OK, replace the

bearings.

5DA3 no signal or speed measured too low in relation to the front wheel:

Faulty sensor or missing

sensor/tone wheel. Or excessive distance between the sensor and the tone wheel or tone wheel with

wrong number of teeth.

Troubleshooting:

Check that the speed sensor and the tone wheel are installed. If they are not, install

them. If they are, check the speed sensor retainer. If it is not OK, restore it. If it is, check if the tone

Norge GT 8v

Electrical system

ELE SYS - 105

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды