MOTO GUZZI NORGE GT 8V Скачать руководство пользователя страница 169

Страница: 169 / 357

•

Undo and remove the two screws.

•

Remove the alternator frame.

•

Remove the sealing ring if necessary.

See also

Fuel tank

Tensioning the belt

•

Remove the left fairing lug.

•

Undo and remove the two front fixing

screws of the oil radiator.

•

Collect the spacers.

•

Undo and remove the five screws fixing

the alternator belt cover.

•

Remove the oil radiator lower support

bracket and the alternator belt cover.

Locking torques (N*m)

Alternator belt cover screw (radiator bracket
retainer) TCEI M6x40 (2)

10 Nm (7.38 lbf ft)

Alter-

nator belt cover screw - TCEI M6x16 (4)

10 Nm

(7.38 lbf ft)

Norge GT 8v

Engine

ENG - 169

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды