MOTO GUZZI NORGE GT 8V Скачать руководство пользователя | Manualshive

Страница: 272 / 357

background image

Standard rear shock absorber setting is adjusted

to suit most high and low speed riding conditions,

to transport the rider plus luggage.

However, this set can be modified for specific

needs according to vehicle use.

BEFORE MAKING ANY ADJUSTMENTS, WAIT FOR THE
ENGINE AND SILENCER TO COOL COMPLETELY.

ADJUSTMENTS

Regular adjustment (standard):

- rider only.

Half load adjustment:

- (for example, rider with passenger or with luggage).

Maximum load adjustment:

- (e.g. rider, passenger and luggage).

CAUTION

SET SPRING PRELOADING AND SHOCK ABSORBER REBOUND DAMPING ACCORDING TO
THE VEHICLE USE CONDITIONS. HYDRAULIC REBOUND DAMPING MUST ALWAYS BE IN-
CREASED TOGETHER WITH SPRING PRELOAD TO PREVENT UNDESIRABLE BOUNCING. IF
NECESSARY, CONTACT AN Official Moto Guzzi Dealer. TRY RIDING THE VEHICLE ON THE
STREET UNTIL THE OPTIMUM ADJUSTMENT IS OBTAINED.

SHOCK ABSORBER SETTING TABLE

Regular load adjustments are the standard settings by manufacturer

REAR SHOCK ABSORBER ADJUSTMENT

Specification

Desc./Quantity

Preload - regular load conditions

25 clicks from fully unloaded

Preload - half-load conditions

35 clicks from fully unloaded

Preload - maximum load conditions

completely screwed

Rebound - regular load conditions

10 clicks starting with the screw (1) fully tightened

Rebound - half -load conditions

10 clicks starting with the screw (1) fully tightened

Rebound - maximum load conditions

6 clicks starting with the screw (1) fully tightened

(1) THE SETTING SHOWN IN THE TABLE MAY NEED TO BE MODIFIED ACCORDING TO THE
TYRE AND ROAD TYPE.

Suspensions

Norge GT 8v

SUSP - 272

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

«
...
270
271
272
273
274
...
»

Содержание NORGE GT 8V






































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NORGE GT 8V

Бренд: Suzuki Страницы: 59

Бренд: LSL Страницы: 4

Бренд: MSA Страницы: 163

Бренд: Ohlins Страницы: 4

TXT PRO - PART LIST 2010

Бренд: GAS GAS Страницы: 64

Бренд: B-PWR Страницы: 13

LIX9U0003740299

Бренд: X-lite Страницы: 116

Бренд: hepco & becker Страницы: 3

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 134

Бренд: Yamaha Страницы: 134

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 164

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 80

Бренд: DYNATEK Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды