MOTO GUZZI NORGE GT 8V Скачать руководство пользователя страница 121

Страница: 121 / 357

•

Check the sensor connector and the instrument panel connector (PIN 3): if they are not OK,

restore. If OK, check continuity of the purple cable between the sensor connector and the

instrument panel connector PIN 3: if not OK, restore the cable harness; if OK, replace the

sensor.

Oil pressure failure DSB 08

Error cause

•

An oil sensor fault is signalled when, with engine running, it is detected that the sensor circuit

is closed. There is an error when the general warning light turns on.

Troubleshooting

•

Detach the sensor connector and check the purple cable is ground insulated: if there is

continuity to ground, restore the cable harness; if it is ground insulated, replace the switch.

It this error persists, use a pressure gauge to check the pressure of the oil in the engine

circuit

Neutral sensor

Function

it tells the gear position to the control unit: in neutral or in gear.

Operation / Operating principle

for gear in neutral, the circuit is closed to ground connection: then, via CAN, the control unit sends the

signal to the instrument panel which turns on the neutral speed warning light.

Level in electrical circuit diagram:

start-up enabling switches

Location:

•

Sensor: rear / upper side of the gearbox

•

Connector: on the sensor

Electrical characteristics:

•

Gear in neutral: closed circuit (0 V on wire from control unit to sensor / switch in continuity).

•

Gearshift engaged: open circuit (12 V on wire from control unit to sensor / open switch,

infinite resistance)

Pin-out:

•

PIN 1: Voltage 12V

NAVIGATOR: STATUSES

Gear in neutral

Example value:

yes/no

DIAGNOSIS

•

Indication on the instrument panel always gear engaged: check the control unit connector

and the sensor connector: if they are not OK, restore the cable harness; if OK, disconnect

Norge GT 8v

Electrical system

ELE SYS - 121

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды