MOTO GUZZI NORGE GT 8V Скачать руководство пользователя

Страница: 330 / 357

REPLACE THE ABS CONTROL UNIT

VEHICLE PREPARATION

•

Connect the bleed bottle to the bleed

screws of the front and rear callipers

and open it.

•

Fully press down the lever and the

brake pedal and fix them into position

with the respective locking devices.

•

Close the bleed screws of the front and

rear callipers and remove the bleed

bottle.

•

Remove the damaged ABS control

unit.

Note: First of all, detach the brake pipes that

go from the ABS control unit to the brake pump

(1-4) and immediately seal the opened unions

of the ABS control unit with protective caps.

Afterwards, remove pipes (2-3) that go from the

ABS control unit to the brakes and also seal

these unions with protective caps.

•

Install the new ABS control unit, previ-

ously filled up.

•

So that the brake fluid remains in the

ABS control unit, first remove the pro-

tective caps of the braking circuit un-

ions and connect the respective pipes.

Once all the braking circuits have been con-

nected, remove the protective caps from the

braking pump unions and connect the braking

pump pipes to the ABS control unit.

•

Unlock the lever and the brake pedal.

•

Remove the reservoir cap and fill it with

new brake fluid up to the reference

"MAX".

CAUTION

PERFORM THE REGULAR BRAKING SYSTEM BLEEDING,
AS DESCRIBED AT THE END OF THE CHAPTER.

•

Always fill the reservoir up to the reference "MAX" and refit the cap.

Braking system

Norge GT 8v

BRAK SYS - 330

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды