MOTO GUZZI NORGE GT 8V Скачать руководство пользователя

Страница: 191 / 357

Checking the valve guides

Use a punch to extract the valve guides from the heads.

The valve guides should be replaced only if the clearance between them and the stem cannot be elim-

inated by simply replacing the valves.

To refit the valve guides on the head, follow this procedure:

•

Heat the head in an oven at about 60°C (140°F).

•

Lubricate the valve guide.

•

Fit the circlips.

•

Press the valve guide with a punch.

•

Use a reamer to bore the holes the valve stems slide through so that the inside diameter is

at the prescribed value. The interference between the seat on the head and the valve guide

must be 0.046 - 0.075 mm (0.0018 - 0.0030 in)

VALVE GUIDE COUPLING - VALVES (INLET)

Specification

Desc./Quantity

Valve guide inside diameter

5.0 ÷ 5.012 mm (0.19685 ÷ 0.19732 in)

Valve stem diameter

4.972 ÷ 4.987 mm (0.19574 ÷ 0.19633 in)

Fitting clearance

0.013 ÷ 0.040 mm (0.00051 ÷ 0.00157 in)

VALVE GUIDE COUPLING - VALVES (OUTLET)

Specification

Desc./Quantity

Valve guide inside diameter

5.0 ÷ 5.012 mm (0.19685 ÷ 0.19732 in)

Valve stem diameter

4.960 ÷ 4.975 mm (0.19527 ÷ 0.19587 in)

Fitting clearance

0.025 ÷ 0.052 mm (0.00098 ÷ 0.00205 in)

Checking the cylinder head

Check that:

•

the faying surfaces with the cover and the cylinder are not scored or damaged, jeopardising

a perfect sealing.

•

Check that the tolerance between the valve guide holes and the valve stems is within the

prescribed limits.

•

Check the valve seats are in good conditions.

INLET VALVE SEAT DETAIL DRAWING

Norge GT 8v

Engine

ENG - 191

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды