MOTO GUZZI NORGE GT 8V Скачать руководство пользователя

Страница: 62 / 357

•

Pull the filler plug / oil level dipstick (1)

straight out.

•

Wipe the oil level dipstick (1) clean and

reinsert it.

•

Pull it out again and check the oil level.

•

The oil level is correct when it is close

to the "MAX" mark. Otherwise, top-up

with engine oil.

Replacement

NOTE

HOT OIL IS LESS VISCOUS AND WILL DRAIN OUT MORE EASILY AND COMPLETELY.

•

Remove the fairing lug

•

Place a container with 4000 cm³ (244

cu.in) capacity under the drainage plug

(2).

•

Unscrew and remove the drainage

plug.

•

Remove the oil level inspection cover

on the left fairing.

•

Remove the dipstick for checking the

oil level (1).

•

Drain the oil into the container; allow

several minutes for oil to drain out com-

pletely.

•

Check and if necessary, replace the

sealing washers of drainage plug (2).

•

Remove any metal scrap attached to

the drainage plug (2) magnet.

•

Screw and tighten the drainage plug

(2).

•

Pour new engine oil until it goes above

the minimum level marked "MIN".

•

Insert the dipstick for checking the oil

level (1).

CAUTION

Maintenance

Norge GT 8v

MAIN - 62

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды