MOTO GUZZI NORGE GT 8V Скачать руководство пользователя

Страница: 107 / 357

1. Engine revolution sensor positive signal.

2. Engine revolution sensor negative signal.

3. Revolution sensor anti-jamming cable.

NAVIGATOR: PARAMETERS

Target engine revs

Example value:

1100 +/- 100 rpm

Parameter valid at idle, setting depends especially on engine temperature: the ECU unit will try to keep

the engine running at this revs, acting on the ignition advance.

NAVIGATOR: STATUSES

Synchronisation

Example value:

Synchronised / Not synchronised

Indicates if the control unit detects the revolution sensor signal correctly

DIAGNOSIS

Engine revolution sensor

An interruption in the sensor circuit has been detected, from PIN 25 to PIN 35 of connector A (BROWN)

Check the sensor connector and the injection control unit connector A (BROWN): it they are not OK,

restore. If OK, check continuity of the two cables leading to PINS 25 and 35 of the control unit connector:

if there is not continuity, restore the cable harness; if there is continuity, check the interruption on the

sensor and replace it.

WARNING If the electric circuit is short-circuited, no error is displayed. Check the sensor electrical

specifications: If they are not correct, replace the sensor. If correct, check supply insulation and ground

connection insulation of both cables. Perform the tests from the sensor connector towards the sensor.

If they are not OK, restore the cable harness or replace the sensor. If OK, perform the tests for pins 25

and 35 of the Marelli control unit connector A (BROWN) towards the cable harness.

Air gap value:

Place the sensor plus the corresponding spacers; the air gap should be between 0.7 and 0.9 mm (0.027

- 0.035 in).

Throttle position sensor

Function

In charge of telling the control unit the position of

the throttle valves.

Operation / Operating principle

The throttle valve position sensor works as a var-

iable resistance according to the throttle rotation.

Level in electrical circuit diagram:

Throttle and

idle motor

Norge GT 8v

Electrical system

ELE SYS - 107

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды