MOTO GUZZI NORGE GT 8V Скачать руководство пользователя

Страница: 297 / 357

Manually assemble the new sealing rings (2) and

(7).

Assemble the bushing (1).

Drive the bushing (1) in with a plastic hammer.

Turn the support (5) over and assemble the other

bushing (8).

TROUBLESHOOTING

Possible Cause

Operation

1. Fitting error of the radial seal or seal damaged 2. Sliding

surface of the wheel axle seal spoiled or damaged

1. Replace the sealing ring and fit it correctly with the suitable
tool

2. Replace the wheel axle

1. Casing not sealed 2. Closing screws of the casing shells not

tightened to the prescribed torque

1. Open the casing shells, clean the surfaces, seal and reas-

semble the casing shells

2. Tighten the closing screws to the correct torque

1. Dirt between the sealing ring and the casing 2. A used seal-
ing ring has been fitted 3. Plug not tightened to the prescribed

torque

1. Clean and tighten to the correct torque

2. Replace the sealing ring

3. Tighten the plug to the correct torque

1. Cap damaged 2. Retaining clamp or closing cover loose 3.

Fitting error of the radial seal or seal damaged 4. Sliding sur-

face of the wheel spacer spoiled or damaged

1. Replace the cap

2. Screw the clamp with suitable pliers

3. Replace the sealing ring and fit it correctly with the suitable

tool

4. Replace the spacer

1. Cap damaged 2. Internal retaining clamp or external closing

clamp loose

1. Replace the cap

2. Screw the internal or external clamp with suitable pliers

1. Bevel gear pair fitting error 2. Bevel gear pair toothing spoiled

or damaged

1. Replace the bevel gear pair

1. Ball bearings on the wheel axle damaged

1. Replace the wheel bearings

Norge GT 8v

Chassis

CHAS - 297

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды