MOTO GUZZI NORGE GT 8V Скачать руководство пользователя | Manualshive

Страница: 3 / 357

background image

SERVICE STATION MANUAL

Norge GT 8v

This manual provides the main information to carry out regular maintenance operations on your scooter.
This manual is intended to

Moto Guzzi Dealers

and their qualified mechanics; several concepts have

been deliberately omitted as they are considered unnecessary. As it is not possible to include complete
mechanical notions in this manual, users should have basic mechanical knowledge or minimum
knowledge about the procedures involved when repairing scooters. Without this knowledge, repairing or
checking the vehicle may be inefficient or even dangerous. As the vehicle repair and check procedures
are not described in detail, be extremely cautious so as not to damage components or injure individuals.
In order to optimise customer satisfaction when using our vehicles,

Moto Guzzi

s.p.a. commits itself to

continually improve its products and the relative documentation. The main technical modifications and
changes in repair procedures are communicated to all

Moto Guzzi Sales Outlets and its International

Subsidiaries

. These changes will be introduced in the subsequent editions of the manual. In case of

need or further queries on repair and check procedures, consult

Moto Guzzi CUSTOMER

DEPARTMENT,

which will be prepared to provide any information on the subject and any further

communications on updates and technical changes related to the vehicle.
2011

NOTE

Provides key information to make the procedure easier to understand and carry out.

CAUTION

Refers to specific procedures to carry out for preventing damages to the vehicle.

WARNING

Refers to specific procedures to carry out to prevent injuries to the repairer.

Personal safety

Failure to completely observe these instructions will result in serious risk of personal

injury.

Safeguarding the environment

Sections marked with this symbol indicate the correct use of the vehicle

to prevent damaging the environment.

Vehicle intactness

The incomplete or non-observance of these regulations leads to the risk of serious

damage to the vehicle and sometimes even the invalidity of the guarantee.

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

«
1
2
3
4
5
...
»

Содержание NORGE GT 8V






































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NORGE GT 8V

Versaflo M Series

Бренд: 3M Страницы: 27

Speedglas 9100 Series

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 5

Бренд: PACIFIC CYCLE Страницы: 112

Бренд: Öhlins Страницы: 8

Бренд: DAELIM Страницы: 68

Бренд: X-lite Страницы: 76

Бренд: yasuni Страницы: 12

Stealth Air Cleaner Kit

Бренд: S&S Cycle Страницы: 4

Бренд: Ducati Страницы: 77

1999 Shadow Aero VT1100C3

Бренд: Honda Страницы: 226

Grizzly Minicross RCX/12 50CC

Бренд: Malaguti Страницы: 33

Windscreen N20012A

Бренд: VStreamT Страницы: 3

Бренд: AC Schnitzer Страницы: 44

XRM125 CFT125 2020

Бренд: Honda Страницы: 111

Бренд: DYNATEK Страницы: 3

Бренд: DYNATEK Страницы: 6

Бренд: DYNATEK Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды