MOTO GUZZI NORGE GT 8V Скачать руководство пользователя

Страница: 316 / 357

The system operates perfectly just as any other braking system without ABS.

The detection of malfunctions may require more or less time according to the type of failure.

Error detection logic foresees that for the errors to be diagnosed one or more conditions must persist

within a given time.

If during this given time one of the conditions is missing but then it comes back, the timer is reset and

the system is no longer able to diagnose the error.

The ABS system is still inactive.

Example:

- error code

5D93

requires some minutes before it is diagnosed during the given time: the ABS warning

light ABS keeps flashing.

ABS FAULTS - GUIDE TO THE DIAGNOSIS

1. ABS WARNING LIGHT ON

2- CONNECT NAVIGATOR

DOES NAVIGATOR COMMUNICATE? (NO, go to 3; YES, go to 4)

3.PERFORM THESE CHECKS:

•

A. Ground connection PIN 1

•

B. +12V at PIN 18

•

C. +12V at PIN 4 with key ON

ARE THERE ANY ERRORS? (YES, go to 5; NO, go to 6)

5. CONSULT THE ERRORS TABLE

6. ABS WARNING LIGHT ACTIVATION

ACTIVE?(YES, go to 7; NO, go to 8)

7. CONTACT TECHNICAL SERVICE

8. CHECK:

•

A. Cable continuity between PIN 8 of the ABS control unit connector and PIN29 of the in-

strument panel.

•

B. Check connectors - refer to the operations described in the chapter

If the previous checks are OK, the causes might be:

•

C. ABS control unit malfunction

•

D. Instrument panel malfunction

Using Navigator for the abs

Braking system

Norge GT 8v

BRAK SYS - 316

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды