MOTO GUZZI NORGE GT 8V Скачать руководство пользователя

Страница: 109 / 357

connector A (BROWN) and PIN C of the sensor (red cable): if there is not continuity, restore

the cable harness; if there is continuity, check continuity of the sensor between PIN A and

PIN C: if there is not continuity, replace the potentiometer; if there is continuity, check the

resistance. If resistance is over 2.5 kOhm, it means the red cable is shorted to positive and

the cable harness should be restored

•

shorted to negative: disconnect the sensor connector and check the ground insulation of the

red cable (from throttle sensor connector or control unit connector): if there is continuity to

ground, restore the cable harness; if it is ground insulated, the resistance between PIN A

and PIN C is below 1.3 kOhm; therefore, the throttle body should be replaced

NAVIGATOR: ADJUSTMENT

Throttle position autodetection

: It allows the control unit to detect the closed throttle position; just

press the Enter key.

Self-adjustable parameters reset

: Lambda probe self-adaptability parameters reset: operation to be

carried out after the throttle body is cleaned or in the case a new engine, a new lambda probe or a new

injector is fitted, or the correct operation of the injection system or the valves is restored.

NAVIGATOR: RESET PROCEDURE

Once the throttle body or the injection control unit is replaced, it is necessary to connect to the diagnosis

instrument selecting FUEL INJECTION and carry out the operation: Throttle position autodetection.

Engine temperature sensor

Function

tells the engine temperature to the control unit so

as to optimise its operation.

Operation / Operating principle

NTC type sensor (resistance sensor, inversely

variable with temperature).

Level in electrical circuit diagram:

Temperature

sensors

Location:

•

sensor: inside the "V"

•

Connector: on the sensor

Electrical characteristics:

NGINE

TEMPERATURE

SENSOR

RESISTANCE

Specification

Desc./Quantity

Resistance at -40 °C (-40 °F)

100.950 kOhm

Resistance at -30 °C (-22 °F)

53.100 kOhm

Resistance at -20 °C (-4 °F)

29.120 kOhm

Resistance at -10 °C (14 °F)

16.600 kOhm

Resistance at 0 °C (32 °F)

9.750 kOhm

Norge GT 8v

Electrical system

ELE SYS - 109

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды