MOTO GUZZI NORGE GT 8V Скачать руководство пользователя

Страница: 49 / 357

Crankcase - crankshaft - connecting rod

CRANKSHAFT SEAT (TIMING SYSTEM SIDE)

Specification

Desc./Quantity

Diameter of crankshaft main journal, timing system side

37.975 - 37.959 mm (1.49507 - 1.49444 in)

Inside diameter of crankshaft bushing, timing system side

38.016 - 38.0 mm (1.49669 - 1.49606 in)

Clearance between bushing and main journal (timing system

side)

0.025 - 0.057 mm (0.00098 - 0.00224 in)

CRANKSHAFT SEAT ( CLUTCH SIDE)

Specification

Desc./Quantity

Diameter of crankshaft main journal, clutch side

53.97 - 53.961 mm (2.12480 - 2.12444 in)

Inside diameter of crankshaft bushing on clutch-side flange

54.019 - 54.0 mm (2.12673 - 2.12598 in)

Clearance between bushing and main journal (clutch side)

0.030 - 0.058 mm (0.00118 - 0.00228 in)

Slot packing system

•

Fit both pistons on the connecting rods.

•

Working from both sides, fit the gasket

between the crankcase and the cylin-

der on the crankcase.

•

Fit both cylinders.

•

Take the left cylinder piston to TDC and

lock crankshaft rotation.

Specific tooling

020675Y

Service shaft gear lock

•

Thoroughly clean the upper surface of

both cylinders.

•

Place the tool on the left cylinder to de-

termine the "squish" (X).

•

Fasten the tool with the nuts of the stud

bolts.

Specific tooling

020676Y

Comparator support for piston posi-

tion checking

Norge GT 8v

Characteristics

CHAR - 49

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание NORGE GT 8V






































































































































































































































































































































































Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды

MOTO GUZZI NORGE GT 8V, Руководство по обслуживанию станции

Результаты поиска

Содержание NORGE GT 8V

Отзывы:

Похожие инструкции для NORGE GT 8V

Бренды по названию

Популярные бренды