manualshive.com logo in svg

Mitsubishi LE-30CTN, Инструкция по эксплуатации

Инструкция по эксплуатации для Mitsubishi LE-30CTN доступна для скачивания бесплатно на manualshive.com. Этот ресурс поможет вам ознакомиться с основными функциями и возможностями продукта. Не забудьте загрузить свой руководство, чтобы всегда иметь доступ к необходимой информации.

Поделиться
Скачать
background image

4.3 Adjustment of tension detector

4. Adjustment and Initial Setting

22

4.2.2

Moving to the adjustment mode screen

1) When the password is not set (the default is remained as 0), the adjustment/setting item selection screen

is displayed wen the power is turned ON in an adjusting mode (DIP.SW is turned OFF).

2) When the password is set to other than zero, the password input screen is displayed when the power is

turned ON in the adjustment mode (DIP.SW8 is turned OFF). The screen cannot be moved to the
adjustment/setting item selection screen without inputting the password set in this screen. 

1) When the password is not set (the default is

remained as 0).

The adjustment/setting item selection screen is
displayed and various adjustments/settings are
available.

2) When the password is set to other than 0.

[1] The password input screen is displayed.
[2] Input the password set on the password set-

ting screen and then press the 

T

 key.

• When the password is valid, the 

adjustment/setting item selection screen 
is displayed and various adjustments/
settings are available. 

• When the password is invalid, 

"INCORRECT" is displayed. Input the 
correct password and then press the 

T

 

key.

4.3

Adjustment of tension detector

4.3.1

Full-scale tension value and decimal point setting

 - - - -  Item number : 20

• Set the full-scale tension value and the position of the decimal point. The full-scale tension value should be

higher than the maximum tension value for control. (The full-scale tension should be approximately 1.2 to
1.5 times higher than the maximum tension.)

• The set full-scale tension value will be used as the maximum tension value in setting analog input signals

and in monitoring output tension values.

• Analog input signal (AI1, AI2)

 - - - - - Input voltage of 0 to 5 V = Tension setting of 0 to full-scale value

• Output signal (AO1)- - - - - Output voltage of 0 to 5 V = Monitor value of 0 to full-scale value

• Setting range

• Full-scale tension value - - - -  1 to 2000 (N, 

×

10N)   - -  Initial setting = 500

• Decimal point  - - - - - - - - - - -  0.01, 0.1, 1 - - - - - - - - -  Initial setting = 1

• Set these values considering the unit of tension set by DIP switch 1 and the maximum tension value for

control.

• Setting method  - - -  In the adjustment mode (turn OFF DIP switch 8, and then turn ON the power to enter

the adjustment mode), select item number 20. The following screen will appear. Using
this screen, set the full-scale tension value and the position of the decimal point.

• At the change of full-scale tension value, be sure to adjust the zero point and the span.

 (1) The password 
       is set to 0

 (2) The password is 
      set to other than 0.

Power-on

Using the value setting dial(16), set 
the item number to [20], and then 
press the 

 key.

Using the 

 or 

 key, move the 

under-cursor to the desired item, and 
then set the value using the value 
setting dial(16).

Adjustment/setting 

item selection screen

Turn on DIP switch 8, and then turn on the power.

Содержание LE-30CTN

































































Отзывы:

Нет отзывов

Похожие инструкции для LE-30CTN

C.Nord GSM Operation Manual preview
GSM
Бренд: C.Nord Страницы: 100
3Com CoreBuilder 9000 Getting Started Manual preview
CoreBuilder 9000
Бренд: 3Com Страницы: 78
Eaton CF2000 Installation And Operation Manual preview
CF2000
Бренд: Eaton Страницы: 100
ZKTeco F6 Installation Manual preview
F6
Бренд: ZKTeco Страницы: 2
FASAR ELETTRONICA FE230 Quick Start Manual preview
FE230
Бренд: FASAR ELETTRONICA Страницы: 2
Faro Barcelona 33929 Installation Manual preview
33929
Бренд: Faro Barcelona Страницы: 8
Faro 33928 Installation Manual preview
33928
Бренд: Faro Страницы: 3
YASKAWA G7 Series Technical Manual preview
G7 Series
Бренд: YASKAWA Страницы: 456
Eaton LS Series Instruction Leaflet preview
LS Series
Бренд: Eaton Страницы: 2
Parker ACR7000 Series Hardware Manual preview
ACR7000 Series
Бренд: Parker Страницы: 21
Parker AC890PX Series Quick Start Manual preview
AC890PX Series
Бренд: Parker Страницы: 26
Parallax 700-10016 Manual preview
700-10016
Бренд: Parallax Страницы: 3
Vageo DT-1 Manual preview
DT-1
Бренд: Vageo Страницы: 2
York CIW01 Installation & Maintenance Manual preview
CIW01
Бренд: York Страницы: 24
Zamel Extra Free RZB-02 Quick Manual preview
Extra Free RZB-02
Бренд: Zamel Страницы: 2
Yamaha DCP4S-US Owner'S Manual preview
DCP4S-US
Бренд: Yamaha Страницы: 2
Eaton EZD Series User Manual preview
EZD Series
Бренд: Eaton Страницы: 448
Eaton EC4E-221-6D4T1 Hardware And Engineering preview
EC4E-221-6D4T1
Бренд: Eaton Страницы: 57

Бренды по названию

Популярные бренды

Загрузить еще бренды