Mitsubishi LE-30CTN Скачать руководство пользователя страница 13

Страница: 13 / 64

1.3 Functions of DIP switches

1. Outline

1.3

Functions of DIP switches

• Open the door of the panel, and you can see a printed circuit board on the main body side. At the upper left

section of this printed circuit board, there are 8-pole DIP switches.

• When the power is turned on, the set conditions of these switches will be read out.
• Each switch has the following function:

• No.1 - - - Sets the tension unit to (N) or (

10N ).

• No.2 - - -  Sets the taper control method.
• No.3 - - -  Sets the taper control method.
• No.4 - - -  Sets the function of the AO1 output.

• Set tension monitor - - Outputs the target tension

value in the automatic
control mode.

• Tension monitor- - - - - Outputs

the

material

tension value detected by
the tension detector.

• No.5 - - - Sets the language to be displayed on the liquid

crystal display.

• No.6 - - -  (No function is assigned.)
• No.7 - - -  Resets data to the initial values for factoring default settings.
• No.8 - - -  Sets the operation mode or the adjustment mode.

• Before setting the DIP switches, be sure to externally cut off the power of all the phases. If the powers

to all the phases are not cut off, you may get an electric shock, or the product may be seriously
damaged.

DIP switches

Setting for taper control method

Before changing the set position of a switch,
be sure to turn the power off.

Set tension

monitor

initialization

Operation

OFF

SW.No

SW. No.6 is set ON and other SW are set OFF
when the product is delivered from the factory.

Unit of tension

Taper control

method

Taper control

method

AO1 output

Language

selection

Language

selection

Data

initialization

Operation

mode

Japanese

English

×10N

Tuning

initialization

Chinese

Tension

monitor

SW.No

Item

OFF

No taper control

Reel diameter
internal calculation method

External reel diameter
signal method

No taper control

Setting for language

SW.No

Language

OFF

English

OFF

Chinese

Japanese

OFF

Содержание LE-30CTN

































































Результаты поиска

Содержание LE-30CTN

Отзывы:

Похожие инструкции для LE-30CTN

Бренды по названию

Популярные бренды

Mitsubishi LE-30CTN, Инструкция по эксплуатации

Результаты поиска

Содержание LE-30CTN

Отзывы:

Похожие инструкции для LE-30CTN

Бренды по названию

Популярные бренды