Mitsubishi LE-30CTN Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 64

background image

2.2 Wiring

2. Installation and Wiring

14

2.2.2

Basic wiring

- - - - - - - - - - - - - - - - - - - - - - - - For conformity to the CE marking, refer to Chapter 13.

• To control the tension using the LE-30CTN tension controller, perform at least the following wiring.

[1] Connect the AC power supply line of 100 ~ 240 VAC and 50 / 60 Hz between terminals L and N.

When maximum output between PP and PN is readed, the power consumption will be 400 VA.

[2] Perform grounding (grounding resistance 100

Ω

or less) to the grounding terminal and the metal plate.

[3] Connect the tension detector.
[4] If the powder clutch/brake or the hysteresis clutch/brake is used, connect the actuator between

terminals [PP] and [PN]. If the rated current of the powder clutch/brake is 3 A or more, connect the
[TOUT] - [AOC] signal line to the input terminal of the power amplifier that is optimum for the rated
current of the powder clutch/brake, and connect the powder clutch/brake to the output terminal of the
power amplifier.
If the torque controllable servomotor is used, connect the [TOUT] - [AOC] signal line to the torque
command terminal of the servo amplifier.

[5] Connect the start/stop signal line to the [RUN] and [MIC] terminals.

Caution:To perform automatic operation, be sure to turn the [RUN] input signal OFF and

ON according to the machine operation status (run or stop).
If this signal is kept at the ON status, restarting the operation of the stopped
machine may apply extremely strong tension to the material, and the material may
fracture.

• To use various functions, refer to Sec. 5 and subsequent sections.

2.2.3

Wiring of tension detector

[1] While ignoring the loading direction (compression or pulling), connect the cable of the tension

detector as shown in the above figure. The loading direction will be automatically detected.

[2] If only one tension detector is used, short-circuit the unused line between the input terminals ( [GRR]

and [WHR] or between [GRL] and [HWL] ).

• Do not connect any 380-VAC power line to the power supply terminals [L] and [N]. The product

may be seriously damaged.

24 VDC, 3 A or less
Powder clutch / brake
Hysteresis clutch / brake

MC1

DC0 to 5V
Servo amplifier
Power amplifier

Grounding resistance

100

Ω

or less

RUN / STOP

LE-30CTN

Green

White

Red

Black

5V

FG

8V

Tension detector

(Right)

Tension detector

(Left)

L

PP

PN

TOUT

AOC

MIC

RUN

RED

BLK

S G

S G

GRL

WHL

GRR

WHR

N

Connect one of the
following actuators.

Power supply

AC100 to 240V

50 / 60Hz

+10%

-15%

Green

White

CAUTION

Do not connect any
380-VAC power line to
the power supply
terminals [L] and [N].
The product may be
seriously damaged.

«
...
14
15
16
17
18
...
»

Содержание LE-30CTN

































































Отзывы:

Нет отзывов

Похожие инструкции для LE-30CTN

Бренд: Canarm Страницы: 3

Бренд: Bartec Страницы: 26

Бренд: Baninni Страницы: 26

Бренд: V2 Страницы: 48

Бренд: Campbell Страницы: 3

Бренд: Omnex Страницы: 9

Бренд: Omegon Страницы: 6

Бренд: WATERLOO Страницы: 8

Бренд: u-blox Страницы: 28

Бренд: u-blox Страницы: 2

Бренд: xpr Страницы: 4

Бренд: National Instruments Страницы: 72

Бренд: National Instruments Страницы: 41

MAGNUM ALERT 3000 FIRE ALARM

Бренд: NAPCO Страницы: 2

Бренд: Warner Electric Страницы: 4

Бренд: HQ Power Страницы: 23

Бренд: ECKELMANN Страницы: 147

Бренд: Squizz Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды