Mitsubishi LE-30CTN Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 64

background image

25

4.4 Automatic operation check

4. Adjustment and Initial Setting

4.4

Automatic operation check

• Basic setting for automatic operation is completed when the full-scale tension value is set and the zero point

and span of the tension detector are adjusted. Turn ON DIP switch 8 (to enter the operation mode), and then
check basic operation while following the procedure below.

4.4.1

Drive system operation check in manual operation mode

1) Turn on the power.

→

The power indicator LED(3) will light.

2) Press the manual control mode selection key(13) to enter the manual mode.

→

The MANUAL indicator lamp(10) will light, and the manual setting 1 screen will appear.

3) Start the machine, and check operation while changing the set manual output value using the value setting

dial(16).

[1] Check operation of the machine.
[2] Check that the tension monitoring graph shown on the LCD and the monitor value shown on the

monitor display(7) vary depending on the change to the set value.

[3] Check other operations.

4.4.2

Operation check in automatic operation mode

1) Turn on the power.

→

The POWER indicator LED(3) will light.

2) Press the automatic control mode selection key(12) to enter the automatic mode.

→

The AUTO indicator LED(13) will light, and the tension setting screen will appear.

3) Start the machine, and then turn ON the [RUN] input signal to start automatic operation. Check operation

while changing the set tension value using the value setting dial.

[1] On the LCD display(5), check that the tension monitoring graph is positioned at the same point as the

set tension graph.

[2] Check that the set tension value displayed on the LCD display(5) is equal to the monitored tension

value displayed on the monitor display(7).

[3] Check that changing the set tension value can vary the other values displayed.
[4] Check other operations.

Caution: To perform automatic operation, be sure to turn the [RUN] input signal OFF and

ON according to the machine operation status (run or stop).
If this signal is kept at the ON status, restarting the operation of the stopped
machine may apply extremely strong tension to the material, and the material may
fracture.

Set manual output value

Tension monitoring graph

Target tension graph

Shows the target tension value
at automatic control mode.

Tension monitoring graph

Target tension graph

Set tension value

«
...
25
26
27
28
29
...
»

Содержание LE-30CTN

































































Отзывы:

Нет отзывов

Похожие инструкции для LE-30CTN

Бренд: GBD Страницы: 12

Бренд: NEC Страницы: 149

Бренд: NEC Страницы: 13

Бренд: Kasco Страницы: 3

Бренд: C Prox Ltd Страницы: 5

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: Kathrein Страницы: 16

Digiplex DGP-848

Бренд: Paradox Страницы: 20

Бренд: Bardiani Страницы: 96

Бренд: Eaton Страницы: 4

Бренд: LLURIA Страницы: 2

Бренд: Osram Страницы: 3

JetWeb JX2-PRN1

Бренд: Jetter Страницы: 25

infi 90 IMMFP12

Бренд: Bailey Страницы: 75

iSteam 2.0 Control

Бренд: mr. steam Страницы: 16

Бренд: Sygonix Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды