Mitsubishi LE-30CTN Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 64

background image

29

5.4 Taper control function

5. Automatic Operation and Functions

5.3.2

Gain 1 and Gain2 setting

- - - - - - - - - - Item number : 11

• In the adjustment mode (power ON with DIP. SW8 OFF), select item number 11 to set these values.
• If it is not necessary to correct the inertia for acceleration or deceleration, it is not necessary to change the

initial values.

On the adjustment/setting item selection screen, set the item number to [11],
and then press the

T

key.

•Setting range

•Gain 1 - - - - 5 to 400% - - - - Initial value=100%
•Gain 2 - - - - 5 to 400% - - - - Initial value=100%

5.4

Taper control function

5.4.1

Outline of taper control

• Taper control is used to change the tension depending on the variation in reel diameter.
• Taper control is mainly used for winding operation. As the reel diameter increases, the controller reduces

the tension to prevent the material from winding too tight or too loose on the reel.

• Following two methods are presently available to determine the current reel diameter.

[1] Reel diameter internal calculation method

• If the tension is kept constant during automatic control, the control output will be changed in

proportion to the reel diameter. While judging the increase in the control output as an
increase in the winding diameter, the controller will judge the reel diameter.

• This method does not need the reel diameter signal, however, a mechanical loss, change in

the actuator torque characteristic, etc. may affect the taper control.

[2] External winding diameter signal method

• The external analog voltage signal that is in proportion to the reel diameter is used for taper

control. Taper control which is proportional to a winding diameter is available.

5.4.2

Selection of taper control method

• Select the taper control method by DIP switch 2 and 3.

Adjustment/setting

item selection screen

SW.No

Item

2

3

ON

OFF

ON

ON

ON

OFF

OFF

OFF

No taper control

Reel diameter
internal calculation method

External reel diameter
signal method

No taper control

«
...
29
30
31
32
33
...
»

Содержание LE-30CTN

































































Отзывы:

Нет отзывов

Похожие инструкции для LE-30CTN

Бренд: UniKey Страницы: 20

Бренд: B&G Страницы: 2

Бренд: B&K Страницы: 9

Бренд: H3C Страницы: 69

Spartan-3A DSP FPGA Series

Бренд: Xilinx Страницы: 140

Бренд: Climatisation Страницы: 52

Бренд: TECOM Страницы: 8

Бренд: Click2Enter Страницы: 34

Бренд: Sabiana Страницы: 60

ZoneSense Plus AS

Бренд: Halma Страницы: 58

Бренд: DSC Страницы: 16

Q.PEAK DUO XL-G11S.X / BFG Series

Бренд: Qcells Страницы: 26

Бренд: EpiSensor Страницы: 37

Бренд: Potter Страницы: 25

Бренд: Bardiani Valvole Страницы: 118

Бренд: Gateway Страницы: 2

Бренд: CALEFFI Страницы: 6

Бренд: Oriental motor Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды