Mitsubishi LE-30CTN Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 64

background image

13.3 Manufacturer and local representative

13. EC Directives (CE Marking)

54

13.3

Manufacturer and local representative

• Manufactured at: Mitsubishi Electric Corporation Himeji Works

840 Chiyoda-machi, Himeji, Hyogo 670-8677 Japan

• Authorized Representative in the European Community: Mitsubishi Electric Europe B.V.

Gothaer Str. 8, 40880 Ratingen, Germany.

13.4

Measures for EMC

13.4.1 Basic measures for EMC

• Perform the following methods securely to achieve the electromagnetic compatibility.

(1)  Install the equipment inside a closed metallic control box (so that radiated noise is sealed).
(2)  Install a noise filter (so that conduced noise is reduced).
(3)  Perform grounding securely (so that the equipment cannot work as a noise antenna).
(4)  Shield power cables and control cables (so that radiated noise is sealed).
(5) Assure sufficient distance between a noise source and counterpart equipment, or install a noise

source individually inside a control box (so that radiated noise is sealed).

(6) Insulate circuits (so that noise is not conducted).

13.4.2 Control box design and EMC tests

The LE-30CTN is so designed as to be incorporated in other equipment. Make sure to install it inside a control
box (to assure safety, restrain noise radiation and shield noise).
The control box design, internal equipment layout and wiring layout are extremely important to achieve the
electromagnetic compatibility. Design the control box under sufficient consideration of the following items.

Make sure to perform EMC tests using the entire machine or system.

(1)  The control box should be made of metal.
(2)  We recommend using a control box having the electromagnetic compatibility.
(3)  If the control box does not have the electromagnetic compatibility, completely remove the coating

inside the control box main body and on the rear side of the control box cover when performing
grounding using a grounding strap or shielding mesh.

(4) The control box door should get secure grounding to the control box main body.

If the control box door is poorly grounded, the door itself will work as a large antenna and emit noise.
Take the following action.

[1] Make sure that the door is made of metal.
[2] Connect the door to the control box main body with braided wires at as many points as possi-

ble.

[3] Use EMI gasket and conductive packing in areas where the door is in contact with the control

box main body.

(5) Make sure that the inside of the control box is free from metals and conductors whose electrical

connection is insufficient.

(6) Complete grounding of the control box is highly effective to achieve the electromagnetic

compatibility.

EMI gasket

Packing

Door

Apply conductive treatment on
areas in contact with EMI gasket.

Metallic box

Control box

«
...
54
55
56
57
58
...
»

Содержание LE-30CTN

































































Отзывы:

Нет отзывов

Похожие инструкции для LE-30CTN

Бренд: Zolix Instruments Страницы: 22

Бренд: Abus Страницы: 12

Бренд: Jands Страницы: 7

Бренд: hager Страницы: 11

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: OEM Страницы: 8

Бренд: ABB Страницы: 102

Бренд: Quinny Страницы: 21

Бренд: GEA Страницы: 13

Бренд: XtendLan Страницы: 12

Бренд: ZBA Страницы: 27

Бренд: M-system Страницы: 10

653 - AE Series

Бренд: VAT Страницы: 103

Бренд: Case IH Страницы: 81

Бренд: Westfalia Страницы: 18

Бренд: SMC Networks Страницы: 31

Бренд: D+H Страницы: 2

Бренд: GRAUPNER Страницы: 180

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды