Mitsubishi LE-30CTN Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 64

background image

6.1 Contact input signals

6. Functions of Input/Output Signals

32

6.

Functions of Input/Output Signals

6.1

Contact input signals

6.1.1

Run / stop signal

- - - - - - - - - - - - - [RUN] - [MIC]

• Turn ON and OFF this signal according to the run or stop operation for the machine.
• In the automatic control mode, when the [RUN] input signal is turned ON, the automatic operation will be

started.

• For the operation of this signal, refer to Sec. 5.1.

Caution: To perform automatic operation, be sure to turn the [RUN] input signal OFF and

ON according to the machine operation status (run or stop).
If this signal is kept at the ON status, restarting the operation of the stopped
machine may apply extremely strong tension to the material, and the material
may fracture.

6.1.2

General contact signals

- - - - - - - { [MI1], [MI2], [MI3] } - [MIC]

• Select item number 50 in the adjustment mode, and then assign the following functions to the general

contact signals (MI1, MI2, and MI3).

• When the following functions are not necessary, it is not necessary to assign the following functions.

1) Output memory signal

• Signal to store the output value when the [RUN] input signal is turned OFF. For a detailed

description, refer to Sec. 5.2.2.

2) Output gain 1, output gain 2 signals

• Signals to correct the tension changed from the inertia of the reel during the acceleration or

deceleration. For a detailed description, refer to Sec. 5.3.

3) Output ON/OFF signal

• When this signal is turned ON, the control output will be sent out irrespective of the ON/OFF status of

the output ON/OFF key(15) on the panel.

• When this signal is turned OFF, the output ON/OFF key(15) on the panel will be enabled. Pressing

the output ON/OFF key(15) will turn ON or OFF the control output.

• When the control output is turned On, the OUTPUT ON/OFF indicator LED will light.

ON

OFF

ON

OFF

ON

OFF

Output ON/OFF

signal

Output ON/OFF

key(15)

Control output

«
...
32
33
34
35
36
...
»

Содержание LE-30CTN

































































Отзывы:

Нет отзывов

Похожие инструкции для LE-30CTN

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: JDS Uniphase Страницы: 27

Бренд: Danfoss Страницы: 20

Бренд: OEG Страницы: 168

Бренд: 7bit Страницы: 2

Бренд: Jafar Страницы: 15

Бренд: E+E Elektronik Страницы: 20

Бренд: Paradox Страницы: 2

Бренд: Water Specialist Страницы: 60

Бренд: Watts Страницы: 8

TRIO MPC-165 Series

Бренд: Sutter Instrument Страницы: 60

Бренд: Sielco Elettronica Страницы: 15

Бренд: Ezodo Страницы: 7

Бренд: Ublox Страницы: 58

Бренд: Hahnel Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды