Mitsubishi Electric MR-J5 Series Скачать руководство пользователя страница 273 | Manualshive

Страница: 273 / 316

background image

10 USING A DIRECT DRIVE MOTOR

10.2 Startup [G] [WG]

271

10

Magnetic pole detection procedure

■

Magnetic pole detection by position detection method

*1 For the incremental system, the setting of [Pr. PL01] is not required.

NO

YES

YES

NO

YES

NO

Magnetic pole detection

Check that LSP (Forward rotation stroke end), LSN (Reverse rotation stroke end), and EM2 (Forced stop 2) are on, and then cycle
the servo amplifier power. Alternatively, reset the software.

Turn "ON (up)" the DIP switch (SW3-1), and cycle the power of the servo amplifier or reset the software.

Set [Pr. PL08.0 Magnetic pole detection method selection] to "0" (position detection method).

Set [Pr. PL01.0 Servo motor magnetic pole detection selection] to "1" (Magnetic pole detection at initial servo-on after cycling the
power).

Cycle the power of the servo amplifier. Alternatively, reset the software.

Set [Pr. PL09 Magnetic pole detection - Voltage level] to "10" as a guide value.

Execute "Forward rotation CCW" or "Reverse rotation CW" with "Positioning operation" in the test operation mode on MR
Configurator2. Set the travel distance to "0" at this time.

The magnetic pole detection is performed.

Is [Pr. PL09] the final value?

Perform one of the following operations:
alarm reset, servo amplifier power cycling,
or software reset.

Has [AL. 027 Initial magnetic pole

detection error] occurred?

Increase the value of [Pr. PL09] by five.

Have [AL. 032 Overcurrent],

[AL. 050 Overload 1],
[AL. 051 Overload 2],

and [AL. 0E1 Overload warning 1]

occurred?

Cycle the power of the servo amplifier
or reset the software.

Set approximately 70 % of the value set for
[Pr. PL09] as the final setting value. If [AL.
027] occurs with this value, specify a value
intermediate between the value set at [AL.
0E1] and the value set at [AL. 027] as the
final setting value.

Perform one of the following operations:
alarm reset, servo amplifier power cycling,
or software reset.

Set [Pr. PL01.0] to "0" (Magnetic pole detection disabled).

End

«
...
271
272
273
274
275
...
»

Содержание MR-J5 Series





























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J5 Series

Бренд: JBL Страницы: 28

Бренд: Artec Страницы: 2

Бренд: Fender Страницы: 20

Бренд: dB Страницы: 20

TUBE SCREAMER AMPLIFIER

Бренд: Ibanez Страницы: 52

Бренд: Roland Страницы: 6

Digital Technology XTDT3200

Бренд: XTE Electronic Страницы: 12

Бренд: aion Страницы: 9

Pacemaker 30200

Бренд: CSP Products Страницы: 12

Бренд: TRU Audio Страницы: 4

Бренд: Inter-m Страницы: 8

Бренд: Tektronix Страницы: 128

Бренд: DaytonAudio Страницы: 14

Бренд: Audio Research Страницы: 20

Бренд: Chandler Limited Страницы: 2

Бренд: Radial Engineering Страницы: 12

Бренд: AVPro Edge Страницы: 15

Бренд: Inter-m Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды