Mitsubishi Electric LGH-100RX5 -E, Руководство пользователя

Страница: 65 / 107

M1: Motor for exhaust fan
M2: Motor for supply fan
C: Capacitor
GM: Motor for By-pass movement
LS: Microswitch
TH1: Thermistor for outside air
TH2: Thermistor for return air
SW1: Switch(Main/Sub change)
SW2,5: Switch (Function selection)
TM1: Terminal block (Power supply)
TM2: Terminal block
(External control input)
TM3: Terminal block (Monitor output)
TM4: Terminal block (Transmission
cable and monitor output)
TB5: Terminal block
(M-NET Transmission cable)
TAB1,TAB2:Connector(Power supply)
TR1: Control circuit transformer
TR2,TR3:By-pass movement transformer
X10,X11,X12:
Relay contact
X101,X102,X103:
Relay Supply fan speed control
X201,X202,X203:
Relay Exhaust fan speed control
CN1: Connector
(Transformer primary)
CN2: Connector
(Transformer secondary)
CN5: Connector (Thermistor)
CN7: Connector
(Motor for By-pass operation)
TAB3: Tab connector(Fan motor)
TAB5: Tab connector(Fan motor)
CN9: Connector (Fan motor)
CN10: Connector (Fan motor)
CN16: Connector (High/Low/By-pass
switch)
CN32: Connector
(Remote control selection)
SA1: Address setting rotary switch
(10 digit)
SA2: Address setting rotary switch
(1 digit)
Symbol : terminal block
: Connector
: Board insertion connector
or fastening connector of
control board
11.1.3 Wire connection diagram ----- Models LGH-150 and 200 RX
5
* Connect the wires shown as thick lines.
* Be sure to connect the ground wire.
* A power supply isolator must be installed when wiring power supply to unit.
* Always use a single pole isolator for the main switch power connection.
BLACK
BLACK
LS
LS
BLACK
BLACK
RED
WHITE
TR3
RED
WHITE
TR2
x201
x202
x203
x101
x102
x103
M
M
M
1
2
1
M
2
EXHAUST
SUPPLY
EXHAUST
FAN MOTOR
FAN MOTOR
FAN MOTOR
SUPPLY
FAN MOTOR
C
C
C
C
cable
transmission
M-NET
MELANS
(non-polar)
Mr.Slim
output 7 , 8
Malfunction monitor
monitor output 6 , 7
By-pass or Delay2
Sheild Wire
12V or 24V DC
BROWN
RED
TM4
CN16
10
8 7 6 1 2 3
CN5
1
2
9
A B S
X10
CN32
X11 X12
Isolator
TAB2
TAB1
CN9
CN10
TAB5 TAB3
TM3 TB5
Transmission
cable
60DR-E
PZ-
BROWN
TM2
ORANGE
ORANGE
ORANGE
ORANGE
TH2(RA)
TH1(OA)
SW1
SW5
SW2
SA1 SA2
BLACK
GREY
YELLOW
ORANGE
WHITE
BLUE
BLUE
RED
BROWN
BROWN
BLUE
CN7
CN2
CN1
TM1
monitor output
Operation or Delay1
PE
N N
L L
24VDC 2A 5VDC 100mA
MAX 240VAC 2A MIN 220VAC 100mA
(non-polar)
TR1
BROWN
BLACK
GREY
YELLOW
YELLOW
GREY
BLACK
BROWN
WHITE
BLUE
ORANGE
RED
RED
ORANGE
BLUE
WHITE
3 1
Unchanged a-conntact
External control input
A
2nd or later main units
cable
transmission
M-NET
S B
TB5(M-NET)
Sheild Wire
TM4
(PZ-60DR-E)
2nd remote controller
installable)
(*1)
Optional Remote controller
(Max.2 remote controllers
PZ-41SLB-E and PZ-52SF-E cannot
be used when using PZ-60DR-E
(*1)
5VDC 100mA
MIN 220VAC 100mA
24VDC 1A
MAX 240VAC 1A
transmission wire to , on TB5 terminal
B A
2
1
of TM4 terminal block,and connect M-NET
is used as the M-NET System ,connect it to
block.
*When the optional Remote Controller PZ-60DR-E
GM MG
GM MG
x103
x102
x101
x203
x202
x201
2
1
GREEN/YELLOW
POWER SUPPLY
220-240V 50Hz
CN16
(Unchanged a-conntact)
RED
BROWN
YELLOW
ORANGE
GREEN
HI
LO
BY-PASS
M
C C
(*2) LGH-200RX
5
has 2
capacitors per mortor
as following drawing.
(*2)
(*2)
(*2)
(*2)
2nd remote controller (Max.2remote controllers installable cable)
2nd LOSSNAY unit (Up to max 15 units)
(*1)
Definitions of symbols
• PZ-41SLB-E and PZ-52SF-E cannot be used simultaneously.
C-65