micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 6

Страница: 6 / 84

MT-3405D Dual Loop Controller Overview

The MT-3405D can control two separate systems, or “control loops”.

EACH SYSTEM HAS
• A flowmeter input, servo control output, and boom section control outputs.

• Three independent sets of volume and area counters and its own tank volume counter.

• An APPLICATION RATE display, warning light, INCREASE/DECREASE keys, and toggle switch to select AUTOmatic or MANual

control mode.

NOTE: Throughout this manual the terms “Controller”, “Loop” and “Channel” are used interchangeably to describe which

of the two systems is being discussed. In some cases, you will see “Ch1” and “Ch2” used as an abbreviation.

The MT-3405D system is designed to work with all optional subsystems provided by Micro-Trak

®:

• NH3 kits

• EPD kits (electric motor/pump driver modules)

• Hydraulic drive kits

• 2-wire (reversing) ball valve interface kits

Any of these can be used on either Channel 1 or Channel 2 with the appropriate interface kit.

WIDTH

CAL

FLOW

CAL

MIN

FLOW

ADJUST

RATE

TARGET

RATE

SPEED

CAL

INLINE

BYPASS

TEST

SPEED

VOLUME /

MINUTE

DISTANCE

AREA /

HOUR

VOLUME

(1) (2) (3)

RATE

SPEED

AREA

(1) (2) (3)

OFF

CONTROLLER 1 B O O M S

OFF

CAL

CONT

SEL

RESET

CONTROLLER 1

APPLICATION RATE 2

TANK

___

CONTROLLER 2

APPLICATION RATE 1

AUTO

MAN

OFF

AUTO

MAN

MASTER

HOLD

MANAUTO

Lighted LED indicates

source of data shown

in DATA display

DATA display

(counters, rates,

speed, etc.)

Independent sets of +/- keys allow

INCREASE/DECREASE of either Ch1 or

Ch2 Application Rate on-the-go

On/Off

switch turns

console

power On or

Off

Selects Ch1 or Ch2 DATA or

calibration, with selection

indicated by yellow light

above DATA display

Used only to adjust

calibration numbers and reset

totals. NOT used to increase/

decrease application rates

Independent warning lights

for Ch1 and Ch2 indicate

when RATE is off target or if

tank is low

NOTE: Master

Hold puts

BOTH Control

Loops in

HOLD; so

does REMOTE

HOLD

Sensor

(if installed)

Independent

AUTO/

MANUAL

toggle

switches for

each Control

Loop

Ch1 and Ch2 have

independent Application

Rate displays

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды