micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 69

Страница: 69 / 84

IMPORTANT:

Opening the flowmeter will void the Flow

Calibration value assigned to your unit. However, you may

need to take the flowmeter apart for periodic cleaning or to

remove an obstruction.

See Illustration below for flowmeter

reassembly instructions.

TO OPEN THE FLOWMETER

Disconnect the hose from servo valve to manifold. Loosen

the union hex closest to the heat exchanger. Remove the

two “U” bolts that hold the servo/flowmeter assembly to the

brackets. Unscrew the union from the heat exchanger and

remove the servo/flowmeter assembly.
Use running water to rinse the assembly of any accumulated

dirt. Remove the three flowmeter bolts, carefully open the

flowmeter and remove the turbine. Thoroughly clean turbine

and housings of any foreign material (dirt, pieces of teflon

tape, rust on magnets, etc.).
Set and spin the turbine in each flowmeter housing half. It

should spin freely. If not, remove the turbine, wipe the shaft

and try again.

Complete Assembly

FM750 N Flowmeter

P/N 10899

TO ASSEMBLE THE FLOWMETER

Place the servo, flowmeter end up, in a vice or other suitable

fixture. Set turbine in non-sensor housing. Properly position

gasket on housing.

(Gasket may be reused a few times but

will eventually need to be replaced.)

Pipe thread compound

is not absolutely necessary but will insure a good seal. Be

careful not to get compound inside flowmeter or turbine

will stall. Carefully put other flowmeter housing (sensor half)

in place.

(Position the housing so that the two square lugs

are lined up with each other.)

Drop all three bolts into holes.

Hold lock washers in place and finger tighten all three nuts.

Nuts should be torqued to 120 in./lb. (13.56 nw/m). Attach

tag by running wire between a bolt and the housings, and

twisting.
After assembly, shaking flowmeter end-to-end should

produce a “rattling” sound (shaft end play). Blowing into

the meter from either end should cause the turbine to spin

freely. If the turbine only spins from one direction, install the

flowmeter so that the liquid flows in that direction.

NOTE: Start with original calibration number and follow

procedure in manual for verifying flowmeter accuracy.

Appendix F

(cont)

MT-3405D - NH3 Specific

(cont)

Flowmeter Assembly (FM-750 N)

WARNING

TO PREVENT SERIOUS INJURY, DO THE FOLLOWING:

ALWAYS WEAR

gloves, goggles, and other necessary

equipment when handling NH3 apparatus.

DO NOT

cross thread. Use anti-seize lead base thread

compound.

THOROUGHLY BLEED

hoses before disconnecting NH3

apparatus.

COMPLETELY EVACUATE

NH3 apparatus before

servicing.

Housing FM750 SS

Turbine

Gasket

Housing FM750 SS

(Non Sensor)

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды