micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 60

Страница: 60 / 84

NH3500 Kit - P/N 01101

The Liquifier

™

Kit P/N 01097

Main Harness - P/N 14366

E D

15’ 10-Pin M/P Extension Cable - P/N 13222

The Ch2 10-pin connector on the back panel of the

MT-3405D is designed to plug right into the harness P/N

13273 that is included in the NH3 kit. All that is needed is a

10-pin M/P extension cable of the appropriate length.

See

Appendix J for details.

An NH3 system can be connected to Channel 1 using the

NH3 Main Harness (P/N 14366) shown below. The 10-pin

connector at the other end of this harness plugs into the

standard NH3 harness (P/N 13273) that is included in the

NH3 kit. Choose an appropriate length extension cable

(for example, P/N 13222 shown below).

See Appendix J for

various extension lengths.

Appendix F

(cont)

MT-3405D - NH3 Specific

(cont)

Component Parts for MT-3405D for NH3 Kits

NH3500 Kit Installation

Remove any existing metering valves. If the old metering

valve has a built-in manifold, it is recommended to install

a separate new manifold for the NH3500 kit. Another

option, although not recommended, is to use the existing

manifold, making certain the old metering valve is in the

maximum open position to allow for minimal restriction of

flow through the plumbing. There also should not be any

positive shut-off valves installed in the plumbing between

the NH3500 kit shut-off valve and the knives.
Locate a convenient area on the applicator to install the

NH3500 plumbing panel. When selecting an installation

location, keep in mind that the hose from the break-away

coupler must reach the strainer inlet with enough length

to allow for proper operation of the break-away coupler

disconnect mechanism and prevent kinking of the hose at

hinge points. Also, the strainer’s clean-out plug should be

accessible for regular cleaning. Make certain that the area

selected allows for enough length of the manifold hose,

between the manifold and the servo valve outlet, to prevent

kinking at hinge points.

INSTALLATION NOTE:

It is recommended to use an NH3

compatible thread sealing compound such as “Slic-tite paste

with Teflon”, or a similar compound, on all pipe thread

fittings. Slic-tite is manufactured by LA-CO Industries, Inc./

Markal Company.
Remove the NH3500 plumbing panel from the shipping board.

Install the plumbing panel on the tool bar frame using the

bottom brackets, carriage bolts and flange lock nuts. Trim any

excess length off of the bolts if required. Attach the hose from

the break-away coupler to the strainer inlet. Check hose length

for proper operation of the break-away coupler disconnect

mechanism. Next, connect the manifold hose to the servo

valve outlet. Check for proper hose length to avoid kinking

at hinge points.

The Liquifier

™

MAX Kit

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды